Skip header and navigation

8 records – page 1 of 1.

Other Name
"SPEED GUN"
Date Range From
1980
Date Range To
1985
Material Type
Artifact
Materials
STEEL, PLASTIC, FOAM
Catalogue Number
P20120014000
  2 images  
Material Type
Artifact
Other Name
"SPEED GUN"
Date Range From
1980
Date Range To
1985
Materials
STEEL, PLASTIC, FOAM
No. Pieces
5
Height
13
Length
45
Width
32
Description
A. CASE, SPEED GUN, 45CM LONG X 32CM WIDE X 13CM TALL. BLACK SYNTHETIC LEATHER EXTERIOR WITH SILVER TRIM ALONG LID, TWO SILVER METAL CLASPS WITH LOCKS ON FRONT, FOUR ROUND, SILVER METAL FEET ON BACK, AND SILVER METAL HINGES ON BACK. FRONT OF CASE HAS BLACK PLASTIC HANDLE ATTACHED TO SILVER METAL MOUNT. CASE INTERIOR HAS GREEN FOAM INSERTS INSIDE LID AND BASE; BASE FOAM INSERT HAS CUT-OUTS FOR SPEED GUN TO REST. CASE EXTERIOR IS SCUFFED AND WORN; TOP AND FRONT OF CASE STAINED WHITE AND BROWN; HANDLE HAS LABEL RESIDE ON TOP AND INSIDE; FOAM INSIDE CASE IS HAS INDENTS FROM SPEED GUN. OVERALL VERY GOOD CONDITION. B. SPEED GUN, 75.4CM LONG WITH CORD, GUN 30.8CM LONG X 9.2CM WIDE. BLACK METAL GUN BODY WITH CONICAL FRONT END; SPEED GUN HAS BLACK HANDLE WITH ENGRAVED CROSS-HATCHED GRIP, AND BLACK TAPE WRAPPED AROUND THE BASE; BASE OF HANDLE HAS BLACK CORD ATTACHED. CORD HAS WHITE TAPE WOUND AROUND TOP, WHITE RUBBER CABLE GUARD; CORD IS SPIRALED WITH BLACK VEHICLE ADAPTER FITTED AT END; ADAPTER IS BLACK PLASTIC WITH ROUND SILVER METAL FITTING. SPEED GUN HAS BLACK PLASTIC TRIGGER AT FRONT OF HANDLE BELOW BODY; FRONT OF SPEED GUN HAS BLACK FOAM FITTED INSIDE CONICAL END. SPEED GUN BODY HAS WHITE TEXT ON SIDE “SPEEDGUN EIGHT” WITH ARROW RUNNING THROUGH WORDS; BODY HAS SILVER SWITCH, TWO WHITE DIALS LABELLED “ALARM”, SILVER DIAL, AND BLACK PLASTIC SWITCH LABELLED “MAN.” “AUTO” “(REL).” BESIDE TEXT. SPEED GUN HAS WHITE TEXT ON REVERSE SIDE “SPEEDGUN EIGHT” WITH ARROW RUNNING THROUGH TEXT. UNDERNEATH OF SPEED GUN BODY HAS SILVER AND BLACK METAL PLATE FIXED WITH SILVER TEXT “CMI INC, MINTURN, CO. USA, TRANSMITTER TYPE JF100, PAT. NO. 3,689,921 & RE 29, 401, S/N 38-001367”. BACK OF SPEED GUN HAS DARKENED GLASS DISPLAY WINDOW, WITH TWO GREEN AND TWO RED BULBS VISIBLE INSIDE. BACK OF SPEED GUN HAS SILVER SWITCH LABELLED “(CAL), MOV, STA.” BELOW DISPLAY WINDOW, AND BELOW A SECOND SILVER SWITCH LABELLED “OFF, ON”. BACK OF SPEED GUN HAS WHITE TEXT “CMI INCORPORATED” BELOW DISPLAY WINDOW. BODY OF SPEED GUN IS SCUFFED AND WORN, WITH CHIPS IN BLACK PAINT; OVERALL VERY GOOD CONDITION. C. LEATHER CASE, 14.4CM LONG X 6.7CM WIDE. BLACK LEATHER EXTERIOR WITH BLACK COTTON AND FOAM-LINED INTERIOR; FRONT OF CASE HAS GOLD TEXT STAMPED NEAR TOP EDGE “DECATUR ELECTRONICS, INC, 715 BRIGHT STREET, DECATUR, ILLINOIS 82522”. CASE MACHINE-STITCHED ALONG RIGHT AND BOTTOM EDGES; TOP EDGE HAS RIM ENGRAVED IN LEATHER. CASE INTERIOR IS FLAKING; TEXT ON FRONT OF CASE IS WORN AND FADED; OVERALL VERY GOOD CONDITION. D. TUNING FORK, 12.5CM LONG X 2.5CM WIDE. SILVER WITH TWO SQUARE PRONGS AND HANDLE; FRONT HAS TEXT ENGRAVED BELOW HANDLE “65 KPH, X BAND”. BACK HAS TEXT ENGRAVED BELOW HANDLE “11443”. TOP OF HANDLE HAS CUT-OUT CIRCLE IN MIDDLE. TUNING FORK HAS BLACK FOAM RESIDUE ON PRONGS FROM LEATHER CASE INTERIOR; OVERALL VERY GOOD CONDITION. E. TUNING FORK, 12.5CM LONG X 2.5CM WIDE. SILVER WITH TWO SQUARE PRONGS AND HANDLE; FRONT HAS TEXT ENGRAVED BELOW HANDLE “88 KPH”. BACK HAS TEXT ENGRAVED BELOW HANDLE “C22333”. TOP OF HANDLE HAS CUT-OUT CIRCLE IN MIDDLE. TUNING FORK HAS BLACK FOAM RESIDUE ON PRONGS FROM LEATHER CASE INTERIOR; OVERALL VERY GOOD CONDITION.
Subjects
MECHANICAL T&E
Historical Association
SAFETY SERVICES
History
ON DECEMBER 22, 2017, COLLECTIONS TECHNICIAN KEVIN MACLEAN INTERVIEWED TIM STOBBS, FORMER LETHBRIDGE POLICE SERVICES OFFICER, ON THE DONATION OF THE SPEED GUN. ON THE SPEED GUN, STOBBS ELABORATED, “[THE SPEED GUN 8] REALLY CHANGED THE WAY THE WORLD WORKED. [IT] ALLOWED US TO SET AN ALARM, IT COULD BE MOUNTED ON THE DASH OF THE CAR TO BE MOBILE, OR IT COULD BE HELD IN A STATIONARY POSITION.” “THIS IS THE LAST ITERATION OF THE SPEED GUN SERIES OF RADAR THAT THE POLICE SERVICES USED IN THE LATE ‘60S…PROBABLY A LOT OF PLACES USED THEM INTO THE EIGHTIES, AND LATER BECAUSE THEY WERE SUCH A GOOD UNIT. THE SPEED GUN 6 WAS A PRECURSOR TO THIS AND IT WOULD [BE] A PLAIN SPEED GUN WHICH LOOKED IDENTICAL TO [THIS] MODEL. BUT IT HAD NONE OF THE FANCY ITERATIONS LIKE ALARMS AND MANUAL AND AUTO SETTINGS ON IT. IT WAS THE FIRST ITERATION THAT ALLOWED THE POLICE, OR AN ENFORCEMENT AGENCY, TO ACTUALLY HAVE A PORTABLE UNIT THAT THEY COULD HOLD IN THEIR HAND [TO] GIVE THEM A READING ON A CAR…VERSUS EVERYTHING THAT THEY HAD WHICH WAS BUILT INTO THE CAR BEFORE AND ACTUALLY FIXED IN THE CAR. PRIOR TO THAT YOU WOULD BE OUTSIDE AND YOU WOULD HAVE A MOUNTED PIECE THAT WOULD BE A TIMING DEVICE, AND YOU WOULD HAVE PIECES OF TUBING ON THE GROUND AND IT WOULD GIVE YOU SPEED FROM TUBES. THIS WAS A STEP FORWARD INTO THE MODERN 2000 FUTURE. EVERYBODY THOUGHT THIS WAS FROM THE PLANET MARS, IT WAS AWESOME." “THE INITIAL ONES THAT STARTED OUT WERE 6’S…[BY 1979 WHEN I ARRIVED] WE WERE MOVING TO 8’S. 8’S HAD ALL THESE WONDERFUL FEATURES IN THEM, THEY HAD COME SO FAR [WITH] THE ALARM, THE AUTO AND MANUAL SETTINGS, THE STATIONARY MOVEMENT, VERY QUICKLY YOU COULD MOVE FROM STATIONARY TO MOVING. THE INTERNAL CALIBRATION WAS A BIG [FEATURE] BECAUSE YOU COULD VALIDATE YOUR SPEEDS WITH YOUR TUNING FORKS, BUT IT WAS ALWAYS NICE TO JUST PERIODICALLY RUN AN INTERNAL CALIBRATION TO MAKE SURE EVERYTHING WAS RUNNING GOOD.” “THEY ONLY LASTED PROBABLY ANOTHER 5 YEARS AFTER I GOT THERE, IF THAT, BECAUSE WE STARTED MOVING TO…A DOUBLE SYSTEM WHERE WE HAD HARD MOUNTED, MOVING RADAR. IT ALSO DID STATIONARY FRONT AND BACK. WE ALSO STARTED MOVING TO A HANDHELD STATIONARY RADAR, WHICH GAVE US MORE VERSATILITY AS WELL. NOW YOU HAD YOUR RADAR LIKE THIS [SPEED GUN] AND YOU COULD RUN TO THE SIDE, YOU COULD DO MULTIPLE FUNCTIONS AT ONCE.” “[WE RAN] 6’S AND 8’S AT THE SAME TIME.” “THIS PARTICULAR MODEL IS QUITE A HIGH END ONE, IT HAS A NUMBER OF DIFFERENT SETTINGS ON IT AND, YOU CAN LOOK ON THE SIDE AND IT SAYS “ALARM”. THIS WAS A UNIQUE THING BACK IN THE DAY—YOU COULD SET, WHEN YOU WERE TRAVELING DOWN THE HIGHWAY OR ON THE ROAD, A PRE-SET SPEED. LET’S SAY FOR AN EXAMPLE YOU GAVE A 15 KM/H DIFFERENTIAL. YOU WOULD SET THIS AT 65 KM/H AND YOU WOULD PUT THE TOP SWITCH TO THE “ON” POSITION, AND YOU LEAVE THIS BACK ROCKER SWITCH IN THE CENTER POSITION, AND WHEN YOU’RE TRAVELING DOWN THE ROAD, ANY VEHICLE THAT WAS IN VIOLATION OF THAT 65 IT WOULD AUTOMATICALLY BEEP AND IT WOULD LOCK THEIR SPEED ON THE RIGHT HAND SIDE. YOUR PATROL SPEED WOULD BE DEMONSTRATED IN THE GREEN ON THE LEFT HAND SIDE OF THE BACK DISPLAY AND ON THE RIGHT HAND SIDE WOULD BE THE RED DISPLAY WHICH WOULD BE YOUR TARGET SPEED. IT WOULD LOCK IT. WITH RADAR, THIS IS A DEVICE THAT CAN BE USED TO TEST A SPEED OF A MOTOR VEHICLE, BUT THE INITIAL OBSERVATION HAS TO BE MADE BY THE OFFICER TO SAY THAT, “I LOOKED AT A VEHICLE, I SAW THE VEHICLE WAS TRAVELLING AT WHAT I BELIEVE TO BE A SPEED OF FASTER THAN 65KM/H, I CHECKED AND VALIDATED IT WITH MY RADAR.” THIS [SPEED GUN], YOU COULD TOTALLY DEPEND UPON THE RADAR TO LOCK IT UP, EVEN IF YOU DIDN’T SEE THE VEHICLE. THIS ONE WAS A MILE STEP AHEAD OF ANYTHING AT THAT TIME THAT WE HAD.” “[THE SPEED GUNS] WORKED WELL IN COLD, THEY WORKED WELL IN HOT, THEY WERE VERY PORTABLE. WE COULD PUT A BATTERY PACK ON THESE, A 12 VOLT BATTERY PACK AND WE COULD STAND OUTSIDE THE VEHICLE WITH THE BATTERY PACK. THEY WERE A PRETTY GOOD UNIT FOR THE DAY. THE ONLY THING THAT YOU REQUIRED THE OFFICER FOR WAS TO ENSURE THAT YOU DIDN’T GET THE WRONG READING, BECAUSE IF YOU HAVE TWO CARS COMING AT YOU AND YOU HAVE TWO OF THEM IN THE BEAM, THE OFFICER HAS TO MAKE A DIFFERENTIAL WHETHER OR NOT IT WOULD WORK.” “WE HAD A NUMBER OF DASH MOUNTED UNITS WHICH HAD THE SAME CAPABILITIES, BUT NOTHING HAD THE ALLOWANCE FOR YOU TO BE ABLE TO PULL IT OUT IN A SECOND AND POINT IT OUT THE SIDE WINDOW TO CATCH SOMEBODY COMING AT YOU FROM THE SIDE OR THE REAR. IT WAS A VERY UNIQUE AND WELL THOUGHT OF BEAST. THE ONLY PROBLEMS WE HAD WITH THESE IS IF YOU CAN NOTICE THERE IS AT THE END [THERE’S A PIECE THAT LOOKS] LIKE A HORN. ONE OF THE BIGGEST ISSUES IS MOST POLICEMEN ARE RELATIVELY HARD ON EQUIPMENT IN THE CARS. THEY’VE GOT THE [SPEED GUN] AND THEY DROP IT ON THE GROUND AFTER THEY GET A SPEED. WE [USED] TO KNOCK THE HORNS OFF [SPEED GUNS] QUITE A BIT AND HAVE TO SEND THEM BACK, OR THE HORNS [BECAME] DEFORMED, AND THE REASON IT’S DEFORMED IS ITS BEEN DROPPED OR BANGED AGAINST SOMETHING. WHILE THAT WOULD BE A NORMAL FOR THIS TYPE OF INSTRUMENT, THAT WAS THE ONLY WEAK POINT IN THIS. IF YOU LOOK AT THE MORE MODERN HANDHELD UNITS THEY WENT AWAY FROM A HORN AND PUT A CONE ON THE OUTSIDE TO PROTECT THE INTAKE OF THE RADAR UNIT. THIS ONE HERE…HAS A STYROFOAM INSERT [IN] IT [TO PROTECT IT]. THOSE ALSO WERE VERY SUSCEPTIBLE TO BEING BANGED AND SMASHED OUT. WE WERE ALWAYS MAKING SOMETHING NEW TO PUT BACK IN THERE AND GLUE THEM BACK IN TO PROTECT THE INNARDS OF THE UNIT; THAT WAS PRETTY MUCH THE ONLY DOWNFALL OF THE UNIT.” “ANOTHER THING IT HAD, WHICH THE OLD ONES DIDN’T HAVE, IS IT HAS A STATIONARY MODE ON THE TOP SWITCH AND A MOVING MODE. THEN IT ALSO HAD A CALIBRATE MODE. IT HAD AN INTERNAL TESTING SYSTEM THAT WHEN YOU HIT CALIBRATE IT WOULD RUN AN INTERNAL CALIBRATION ON IT TO HELP YOU, WITH YOUR TUNING FORKS, TO ENSURE THAT THIS WAS WORKING RIGHT. YOU WOULD GENERALLY TEST THIS AT THE BEGINNING OF YOUR SHIFT AND IF YOU STOPPED FOR LUNCH YOU WOULD TEST IT AGAIN DURING THE MIDDLE OF YOUR SHIFT. THEN YOU’D TEST AT THE END OF YOUR SHIFT TO VALIDATE THAT THIS INSTRUMENT HAD BEEN OPERATING CORRECTLY DURING THE DURATION OF YOUR SHIFT.” “THIS CALIBRATION INTERNALLY WOULD RUN AN INTERNAL TEST TO MAKE SURE THAT THE CALCULATIONS INSIDE WERE WORKING CORRECTLY, THE ELECTRONICS. BECAUSE THIS IS A PIECE OF ELECTRONICS AND IT IS SUSCEPTIBLE TO HOT AND COLD. THE WHOLE IDEA OF THIS IS TO ENSURE THAT WHEN YOU WENT TO COURT, WITH THE TUNING FORK TEST AND WITH THE INTERNAL CALIBRATION TEST, YOU COULD STAND UP BEFORE THE COURT AND [SAY], “I TESTED THE UNIT, AND IN MY OPINION, AND MY TRAINING, THIS UNIT WORKED CORRECTLY AND AS IT SHOULD TO DETERMINE ACCURATELY THE SPEED OF A MOTOR VEHICLE, EITHER WITH ME MOVING IT OR ME STATIONARY”. YOU HAVE TO GIVE THAT EVIDENCE…AND THAT [CALIBRATION] ALLOWED THAT. [THE] TUNING FORK TEST AND THE INTERNAL [MODE] VALIDATED YOUR ABILITY TO SAY THAT.” “EVERY TIME YOU TOOK OVER A CAR, OR SAY YOU CHANGE CARS MID-SHIFT, [AND] YOU HAD ONE OF THESE UNITS OR ANY RADAR UNIT IN IT, THE FIRST THING YOU’D DO IS YOU WOULD TEST AND ENSURE THE ACCURACY OF THIS UNIT. [THAT WOULD] ENSURE THAT WHEN YOU LEFT, IF YOU GOT SOMEBODY ON RADAR, IT WOULD BE GIVING YOU AN ACCURATE READING. THEY’RE USUALLY ACCURATE, PLUS OR MINUS LESS THAN 1%. AT A 100KM/H IT WOULD BE LESS THAN 1KM/H OFF. THERE ARE VARIOUS THINGS WITH RADAR THAT ARE [BENEFICIAL]. IF YOU’RE SITTING AT THE SIDE OF THE ROAD AND YOU’RE SHOOTING AT AN ANGLE, THE HIGHER THE ANGLE THE LOWER THE SPEED BECAUSE IT’S LIKE A TONE. IF YOU THINK OF RADAR AS HEARING A TRAIN COMING TOWARDS YOU, YOU HEAR IT COMING, IT GETS LOUD, AND THEN IT GOES AWAY AND IT CHANGES TONE. [THE SPEED GUN] GIVES US THE SAME THING AND THAT’S WHAT THIS READS. SO THAT’S GOOD. THIS [SPEED GUN] WAS THE ULTIMATE IN THE SPEED GUNS, THIS WAS EXCELLENT.” “THE COOL THING ABOUT IT WAS FOR THE COURT SYSTEM, IT CAME WITH TWO SETS OF TUNING FORKS. THE TUNING FORKS WERE USUALLY CALIBRATED TO A SPEED. THESE ONES ARE X-BAND TYPE TUNING FORKS, AND THEY WERE SENT AWAY ANNUALLY TO BE CALIBRATED TO ENSURE THAT THEY MAINTAINED THEIR FREQUENCIES. WHAT WOULD HAPPEN IS THAT YOU WOULD TAKE AND PUT [THE SPEED GUN] IN STATIONARY MODE, AND YOU WOULD TEST THE DEVICE TO ENSURE THAT IT WAS ACTUALLY READING CORRECTLY, ON BOTH OF [TUNING FORKS]. YOU TESTED THE COMPUTATIONAL SPEED OF THE UNIT. YOU’D STRIKE TWO OF THE TUNING FORKS AND PUT THEM TOGETHER IN FRONT OF THE UNIT, AND IT WOULD MAKE A COMPUTATION ON THE TWO TONES TO GIVE YOU THE BASIC SPEED DIFFERENTIAL BETWEEN THE TWO TUNING FORKS. THIS WAS ANOTHER MEANS TO ENSURE THAT WHAT YOU’RE DOING IS GETTING THE PROPER SPEED OUT OF YOUR UNIT. IT WAS REALLY A STEP FORWARD IN INSURING THAT THE CREDIBILITY AND CAPABILITY OF THE UNIT WAS VALIDATED, AND THE COURTS ACTUALLY LOVE THAT.” “ANNUALLY YOU RECERTIFY YOUR TUNING FORKS, YOUR TUNING FORK CERTIFICATION FOR TWO TUNING FORKS IS PROBABLY ABOUT $120 A YEAR. IF ANYTHING STARTS HAPPENING TO THESE, BECAUSE THEY GET BOUNCED IN THE CAR, VIBRATION, HOT, COLD, THEY’RE IN THE CAR ALL THE TIME. THEY START TO WEAR OUT. IT STARTS BECOMING COST PROHIBITIVE TO SEND THEM BACK TO THE FACTORY FOR REFURBISHING. THERE’S A THING IN [THE SPEED GUNS] CALLED THE OSCILLATOR. UNDER THE NEWER UNITS THE OSCILLATOR IS IN THE HEAD, AWAY FROM THE MAIN UNIT. THE OSCILLATOR FOR THIS [MODEL] IS BUILT INSIDE, SO YOU HAVE TO TAKE [THE] WHOLE UNIT AND SHIP IT OFF. THEY HAVE TO PEAL IT ALL APART, PUT AN OSCILLATOR INTO IT. WHEREAS WITH THE NEW UNITS, WITH THE SEPARATE HEADS WITH THE OSCILLATOR, YOU CAN JUST GET ANOTHER HEAD, PUT ANOTHER HEAD ON, SEND THAT HEAD AWAY TO THE, AND FOR A $160 YOU GET THE OSCILLATOR FIXED. WHEN THESE START TO BREAK DOWN, IT’S USUALLY CATASTROPHIC. THIS IS USUALLY ALMOST COST PROHIBITIVE—LIKE MOST ELECTRONICS, THEY HAVE A VERY LIMITED SHELF LIFE. THEY DON’T GET TREATED EXACTLY THE NICEST. MOST POLICE CARS WILL HAVE POWER SEATS BECAUSE OF THE AMOUNT OF PEOPLE THAT [HAVE] TO BE IN THEM AND THE DIFFERENT POSITIONS THEY HAVE TO BE IN, AND A REGULAR SLIDING SEAT GENERALLY DOESN’T GIVE ENOUGH TO FIT ENOUGH PEOPLE. IF SOMEBODY HAD USED THIS, AND PUT IT DOWN, AND IT FELL BEHIND THE SEAT, AND THEY PUSHED THE SEAT BACK, THOSE POWER SEATS ARE FAIRLY STRONG, THEY CAN DO A SIGNIFICANT AMOUNT OF DAMAGE TO ONE OF THESE UNITS INADVERTENTLY. YOU HAVE TO ASSESS HOW THEY’VE BEEN TREATED, WHAT THE COST IS GOING TO BE TO MAINTAIN THEM, LONG-TERM INVESTMENT. AS SOON AS A SPEED GUN 8 OSCILLATOR’S DONE, IT’S DONE. BECAUSE IT’S NOT WORTH SENDING IT BACK TO HAVE RE-DONE.” “[THE] TRAFFIC SERGEANT WOULD HAVE BEEN IN CHARGE OF THE PROCUREMENT OF [RADAR EQUIPMENT]. AT THAT TIME I’M NOT SURE WHO WOULD HAVE BEEN SERGEANT, BUT IT WAS ONE OF MY SERGEANTS THERE. HE HAD BEEN ON TRAFFIC FOR QUITE A WHILE AT THE TIME…SHORTLY THEREAFTER, WHILE I WAS TENURED THERE, SERGEANT NORRIS VANHORN WAS ALSO ON TRAFFIC WHEN I WAS ON THERE. THESE [SPEED GUNS] WERE FANTASTIC…WHEN WE GOT THESE, THESE WERE EYE OPENERS…YOU THOUGHT YOU’D DIED AND GONE TO HEAVEN BECAUSE OF THE VERSATILITY IT GAVE YOU TO DO YOUR JOB.” “YOU CHANGE THE TECHNOLOGY TO TRY TO KEEP UP WITH THE NEEDS OF THE GUYS THAT ARE WORKING. IT MAKES YOU MORE EFFICIENT…I MANAGED THE PEACE OFFICERS IN OKOTOKS, AND I CAN TELL YOU, I CAN BUY EQUIPMENT EVERY DAY…THAT STUFF’S CHEAP. PEOPLE ARE EXPENSIVE…YOU WOULD TRY TO KEEP THEM IN EQUIPMENT THAT KEEPS THEM VERY EFFICIENT AND EFFECTIVE, AND YOU’D GET THE MOST BANG FOR YOUR BUCK OUT OF THE PEOPLE WORKING…THIS TYPE OF EQUIPMENT HAS USUALLY A SHORT SHELF LIFE. WE DID OTHER THINGS WITH THEM. WE USED TO LEND OUT THESE RADAR GUNS TO THE SOFT BALL KIDS…OR THE HARD BALL KIDS…AND THEY COULD SEE HOW FAST THEY COULD PITCH. OR WHEN THEY HAD SOAPBOX DERBIES…YOU’D GIVE THESE [SPEED GUNS] AND THEY COULD POST IT ON THE NEWS “AH LITTLE JOHNNY CAME DOWN THE HILL AND HE WAS DOING 37 KM/H IN HIS HOME MADE THING”. THERE [WERE] LOTS OF OTHER APPLICATIONS THAT THIS WAS SORT OF RE-CIRCULATED TO, FOR THE COMMUNITY. IT’S NOT LIKE YOU’D JUST DISCARD THE [EQUIPMENT], YOU’D TRY TO MAKE ANOTHER USE FOR IT. A LOT OF THIS [EQUIPMENT] FOR MANY YEARS, MADE ITS WAY AROUND THE COMMUNITY IN OTHER SOCIAL EVENTS TO ASSIST THE COMMUNITY IN WHAT THEY WANTED TO DO AND SEE.” STOBBS RECALLED HIS TIME WITH THE LETHBRIDGE POLICE SERVICE, NOTING, “I WAS VERY FORTUNATE. I WORKED FOR LETHBRIDGE POLICE SERVICE [STARTING IN 1979]. I ALSO WORKED FOR THE RED CLIFF POLICE SERVICE PRIOR TO THAT, AND WE RAN THESE UNITS WHEN I WAS A YOUNG CONSTABLE. I WORKED IN TRAFFIC FOR OVER 3 AND A HALF OR 4 YEARS.” “THESE [SPEED GUNS] WERE VERY COMMON IN OUR CARS WHEN I CAME HERE. I WAS VERY FORTUNATE—I DROVE A BLACK WIDOW…ONE OF OUR WIDOWS HAD THIS IN IT…WE HAD TWO CARS IN TOWN THAT WERE RENOWNED WITH THE KIDS. THEY WERE TWO BLACK FORDS WITH BIG 429’S IN THEM. THEY HAD SPEED GUNS IN THEM AND THEY ALSO HAD OTHER RADARS IN THEM. THAT [SPEED GUN] WAS ONE OF THE ITERATIONS WE HAD IN THEM, AND WE USED THESE A LOT FOR OUR ENFORCEMENT PROGRAM. THEY COULD GIVE US SUCH VERSATILITY FOR THE OFFICER TO SIT STATIONARY OR TO BE MOVING. WHEN YOU’RE IN A SCHOOL ZONE, SOMETIMES YOU WANT TO STAND OUTSIDE YOUR CAR, YOU WANT TO RUN BACKWARDS, OR YOU WANT TO RUN TO THE SIDE. IF YOU’RE IN A PLAYGROUND ZONE, IT’S MORE ADVANTAGEOUS TO BE SITTING ON A SIDE STREET THAN SITTING WITH THE CARS PASSING YOU. IT GAVE US SUCH VERSATILITY WHICH WE NEVER HAD BEFORE.” “BACK IN THE DAY, OUR FLEET WAS…WE CALLED IT THE ‘SMARTIE’ FLEET. IT WAS MULTIPLE COLOURS AND I DON’T KNOW THE PURPOSE BEHIND IT. WHEN I WAS IN [LETHBRIDGE], IF YOU WOUND UP WITH THE TRAFFIC FLEET WHEN I STARTED IN ‘79, THERE WERE TWO CARS. THERE WERE ALWAYS TWO BLACK CARS, AND THEY WERE CALLED THE BLACK WIDOWS. THERE WERE DIFFERENT ITERATIONS. THE FIRST TWO WERE FORD INTERCEPTORS WITH 429’S ALL DECKED OUT, AND THEY WERE PURSUIT TYPE CARS, THEY ALL WERE IN THOSE DAYS. THEN WE HAD A NUMBER OF OTHER VEHICLES. ONE OF THE CARS THAT, WHEN I FIRST WENT THERE, I DROVE [WAS] A SECONDARY MARKED ENFORCEMENT CAR AND IT WAS A PINKIE SALMON COLOUR. I DON’T EVEN KNOW, AND IT WAS GREAT, BUT IT WAS A GREAT BIG LTD AS WELL. THEN WE HAD A COUPLE OTHER CARS THAT WERE A COLLISION CAR AND A HIT-AND-RUN CAR. THEY WERE DIFFERENT COLOURS AGAIN. I DON’T KNOW WHY THEY BOUGHT THEM THAT WAY, I DON’T KNOW WHETHER THAT WAS THE THOUGHT OF THE CHIEF AT THE TIME, BUT THAT WAS THE WAY THINGS WENT UNTIL FINALLY WE DECIDED LATER ON THAT OUR FLEET WAS GOING TO GO BLACK AND WHITE LIKE IN THE OLD DAYS. BEFORE THE “SMARTIE” FLEET IT WAS BLACK AND WHITE, WE WERE GOING BACK TO BLACK AND WHITE. WE WERE THE FIRST POLICE SERVICE IN ALBERTA THAT WENT BACK TO BLACK AND WHITE AND EVERYBODY’S FOLLOWING LETHBRIDGE SUIT, ACTUALLY. THAT’S A CULTURAL THING THOUGH AND LETHBRIDGE IS VERY PROUD OF THEIR BLACK AND WHITE CARS.” “RADAR WAS A DAY-TO-DAY THING; IT WAS INVOLVED HEAVILY IN A DIRECTED TRAFFIC ENFORCEMENT PROGRAM. WE USED TO HAVE A PIN-MAP, AND WE DIRECTED OUR ENFORCEMENT ACTIVITIES AROUND A NUMBER OF THINGS. FIRST AND FOREMOST WOULD BE OUR PIN-MAP AND OUR PIN-MAP WAS OUR COLLISION MAP. EVERY COLLISION WAS PINNED AND THEY WERE PINNED IN DIFFERENT COLOURS—THIS [IS] OLD TECHNOLOGY. A FATAL WOULD BE BLACK, AN INJURY WOULD BE RED, A NON-INJURY WOULD BE BLUE. WE COULD VISUALLY SEE FROM THE ENFORCEMENT ASPECT WHERE WE SHOULD BE INVESTING OUR TIME TO SLOW PEOPLE DOWN AT THESE COLLISION POINTS. SECONDLY IS, LETHBRIDGE HAD ALWAYS HAD OUR SCHOOLS CLOSE TOGETHER, SO WE INVESTED A LOT OF OUR TIME AND ENERGY AROUND THE SCHOOL SYSTEM. ONE OF THE THINGS THAT I WAS PROUD OF IS, FOR THE SIZE OF THE CITY AND THE TRAFFIC FLOWS THAT WE HAD, OUR FATALITY WITH YOUTH WAS VERY LOW. WE HAD A FEW KIDS HIT IN MY TIME AND A FEW OBVIOUSLY PASSED AWAY, IN A CITY OF THIS SIZE, BUT OVER THE YEARS MOST OF US TOOK GREAT PRIDE IN THE FACT THAT WE HAD AN OPPORTUNITY TO REALLY MAKE A VISUAL AND A NOTED IMPACT ON BEHAVIORS IN SCHOOLS, WHETHER IT BE U-TURNS, SPEEDING, IN THIS. PEOPLE WERE WELL AWARE WE WERE THERE.” “WE HAD AN EXCELLENT RELATIONSHIP WITH THE KIDS…[IN THE 1970S-1980S WHEN] MUSCLE CARS WERE BIG. WE USED TO HAVE A COOL THING GOING WITH SOME OF THESE KIDS WHEN YOU’RE IN THE ENFORCEMENT GAME. WE USED TO HAVE A [SYSTEM OF] EVERY THIRD ONE’S FREE TYPE THING. THEY’D WORK ALL WINTER, A LOT OF THESE KIDS DIDN’T SMOKE, THEY DIDN’T DRINK, THEY DIDN’T DO ANYTHING. ALL THEY WORKED [ON] WAS THEIR CARS, BUT ONCE SPRING ROLLED OUT, OUT CAME THE MUSCLE CARS. OVER THE COURSE OF THE SUMMER THEY DROVE THEM. THEY WOULD END UP AFOUL OF US, WHETHER IT BE FOR STUNTING OR SPEEDING. WITH SOME OF THESE KIDS, WE WOULD HAVE THIS FREQUENT FLYER MILE PROGRAM BECAUSE THEY WOULD GET THEMSELVES INTO A BIND, BUT THEY WERE SUCH GOOD KIDS THEY WERE JUST STUPID WITH THEIR CARS. WE USED TO CATCH THEM FOR SPEEDING WITH THESE [SPEED GUNS], OR STUNTING. THE RELATIONSHIP WITH THE YOUTH, SOME OF THE YOUNGER PEOPLE, THAT ARE LATE-TEENS OR EARLY-TWENTIES WAS PRETTY GOOD, THESE GUYS THAT BUILT THESE CARS UP. WE HAD A PRETTY GOOD KNOWLEDGE OF THEM AND WE WORKED WELL WITH THEM.” “WE RAN WHAT THEY CALLED A “DIRECTED TRAFFIC ENFORCEMENT PROGRAM”. THERE [WERE] A LOT OF OPTIONS FOR THE GUYS TO GO WHERE THEY WANTED, BUT FIRST AND FOREMOST WE CONCENTRATED ON HIGH COLLISION AREAS AND SCHOOLS. OBVIOUSLY WE KNEW WE HAD THE STRIP…WE HAD 3RD AVENUE AND MAYOR MAGRATH DRIVE AND KIDS DROVE THE STRIP IN THE SUMMER, THAT’S WHERE THEY DID THEIR DRAG RACING…BACK IN THE DAY, WHEN I FIRST STARTED, MAYOR MAGRATH DRIVE WENT STRAIGHT THROUGH TO NORTH MAYOR MAGRATH DRIVE. THAT INTERSECTION [OF] 3RD AVENUE, MAYOR MAGRATH DRIVE USED TO GO STRAIGHT THROUGH ON THE HIGHWAY. IT WAS A BUSY PLACE [WITH] LOTS OF COLLISIONS. WE SPENT A LOT OF TIME DOWN IN THERE ON MAYOR MAGRATH, AND THERE WERE OTHER PLACES IN TOWN WHICH WERE CONCERNS. YOU’D GET CITIZENS COMPLAINING ABOUT LOTS OF TRAFFIC AND SPEED, WE WOULD GO DOWN AND MONITOR IT, AND WE WOULD TRY TO RESPOND TO THE NEEDS OF THE COMMUNITY BY ATTENDING THAT AREA. USUALLY IT WAS ONE OR TWO PEOPLE IN THE AREA THAT WERE DOING IT AND YOU CAUGHT AND DEALT WITH THEM, AND THE PROBLEM PRETTY MUCH WENT AWAY. ONE OF THE THINGS I WAS TAUGHT AS A YOUNG CONSTABLE [WAS WHEN YOU] COME TO WORK AFTER YOUR DAYS OFF, THE FIRST THING YOU DO IS YOU GO LOOK AT YOUR PIN BOARD AND YOU SEE IF ANYTHING CHANGED, IF HAVE WE HAD A FATALITY. HAS THERE BEEN SOME SERIOUS COLLISIONS, HAS SOMETHING CHANGED? YOU ALWAYS KNEW IN YOUR MIND WHERE YOU HAD TO BE.” “WE SPENT LOTS OF TIME ON SCENIC DRIVE ANYWHERE. AN OUNCE OF PREVENTION IS WORTH A POUND OF CURE. IF YOU’RE RUNNING A MARKED VEHICLE, SOMETIMES WE WOULD JUST PARK ON A BOULEVARD SOMEWHERE IT WAS BUSY AND JUST SIT THERE. YOU’D MONITOR TRAFFIC AND OF COURSE SOMEBODY WOULD EVENTUALLY DO SOMETHING SILLY AND YOU’D HAVE STOP THEM, BUT THE WHOLE IDEA WOULD BE FOR THE VISIBILITY ASPECT.” “I REMEMBER WHEN WE GOT THE 8’S [SPEED GUNS] AND WE COULD PROGRAM THEM, WE THOUGHT WE’D DIED AND WENT TO HEAVEN. WE ARE ALL ABOUT EFFICIENCY. EVERY SHIFT YOU WOULD DEAL WITH TWENTY, THIRTY PEOPLE OR MORE. NOT INCLUDING COMPLAINTS, WE’RE TALKING ABOUT INTERACTIONS WITH PEOPLE THAT WERE VIOLATIONS SOMEHOW. [THE SPEED GUNS] GAVE YOU A TOOL TO INTERACT WITH SOMEBODY…AND A LOT OF OTHER THINGS COME FROM THIS. A LARGE AMOUNT OF CRIME IS SOLVED BY SOMEBODY STOPPING A CAR AND TALKING TO SOMEBODY, AND THE CAR’S STOLEN, THERE’S STOLEN PROPERTY IN THE CAR, THE GUY’S WANTED ON WARRANTS. THIS TOOL WAS A LEVERAGE AND AN ABILITY TO ENTER A WHOLE NEW REALM IN ASSISTING OUR COMMUNITY AND KEEPING OUR COMMUNITY SAFE. IT JUST WASN’T FROM THE TRAFFIC END OF IT, IT GAVE YOU AN OPPORTUNITY TO INTERACT WITH PEOPLE THAT NORMALLY YOU WOULD NOT HAVE THE CAPACITY TO INTERACT WITH. AND DO IT IN A LAWFUL MANNER.” FOR MORE INFORMATION INCLUDING THE FULL INTERVIEW TRANSCRIPTION AND LETHBRIDGE HERALD ARTICLES, PLEASE SEE THE PERMANENT FILE P20120014000-GA.
Catalogue Number
P20120014000
Acquisition Date
2012-05
Collection
Museum
Images
Less detail
Other Name
TURNOUT PANTS / BUNKER PANTS
Date Range From
1980
Date Range To
2000
Material Type
Artifact
Materials
CANVAS, COTTON, PLASTIC
Catalogue Number
P20150010020
  2 images  
Material Type
Artifact
Other Name
TURNOUT PANTS / BUNKER PANTS
Date Range From
1980
Date Range To
2000
Materials
CANVAS, COTTON, PLASTIC
No. Pieces
3
Length
170.5
Width
61.0
Description
FIREMAN'S TURNOUT PANTS OR BUNKER PANTS. OUTER SHELL, SUSPENDERS, INNER LINER. DIMENSIONS ARE FROM TIP OF SUSPENDERS TO HEM AND WIDTH IS AT WAISTBAND. .A: OUTER SHELL. TAN CANVAS. HEM IS A PLASTICIZED FABRIC. FLORSCENT YELLOW AND SILVER REFLECTIVE STRIPE AT ANKLE. LINER KEPT IN PLACE AT HEM WITH TWO SNAPS: POSTS ON LINER, WITH THE CAPS ON SHORT PIECES OF BLACK NYLON STRAPPING, SEWN TO THE INSIDE OF THE SHELL'S LEG. REINFORCED KNEES AND TWO LARGE POCKETS ON OUTER THIGH AREA, EACH WITH A FLAP THAT CLOSES WITH VELCRO. PANTS CLOSE WITH A VELCRO CLOSURE, A SINGLE SILVER COLOURED SNAP, AND LARGE HOOK AND EYE, WITH THE HOOK AT THE WEARER'S RIGHT HIP AND A D-SHAPED EYE ON THE LEFT SIDE OF THE FLY. HOOK IS AFFIXED TO PANTS WITH THREE SILVER COLOURED METAL RIVETS GOING THROUGH A PIECE OF BLACK LEATHER THAT THE HOOK IS SEWN ONTO. BLACK NYLON STRAPS ON THE WEARER'S HIP ALLOW PANTS TO BE ADJUSTED ONCE ON. BACK OF PANTS CONTINUES UP WEARER'S BACK FOR 14.5CM HIGHER THAN THE FRONT. INSIDE OF WAISTBAND IS NAVY BLUE AND THERE ARE NINE CAPS FOR THE SNAPS THAT ATTACH THE INNER LINER. INSIDE OF FLY LINED WITH BLACK PLASTICIZED MATERIAL. WHITE RECTANGULAR LABEL, WITH NAVY BLUE WRITING: "FIRE SERVICE MANAGEMENT. TEL: (403) 279-5095." BELOW IN RED: "C 5519". ON THE OUTSIDE OF THE PANTS, SIX SILVER COLOURED BUTTONS, WITH STAMPED "GLOBE" IN THE CENTRE ALLOW SUSPENDERS TO BE ATTACHED - FOUR ARE IN THE FRONT, WITH TWO IN THE BACK. .B: SUSPENDERS. RED WOVEN STRAPPING. VERY ENDS OF SUSPENDERS ARE FINISHED IN BLACK LEATHER, WITH EACH OF THE SIX ENDS HAVING A BUTTON HOLE. THE LEATHER PORTION IS SEWN ONTO ELASTICIZED RED STRAPPING. ON THE FRONT, THIS ELASTICIZED PORTION GOES THROUGH A BLACK PLASTIC D-RING, WHICH HAS NON-ELASTICIZED WOVEN STRAPPING ON THE OTHER SIDE. EACH FRONT STRAP HAS A SECOND D-RING TO ALLOW ADJUSTMENT IN LENGTH. IN THE BACK, THE ELASTICIZED PORTION IS SEWN DIRECTLY ONTO THE WOVEN PORTION. STRAPS FORMA ROUGH 'H' SHAPE, WITH THE ELASTICIZED CROSS PIECE GOING ACROSS THE WEARER'S BACK AT THE SHOULDER AREA. SMALL LABEL NEAR THIS CROSS PIECE: "ASSEMBLED IN MEXICO". .C: INNER LINER. LIGHT BLUE/GREY COTTON FABRIC ON ONE SIDE, WITH A PLASTIC/COTTON OFF-WHITE FABRIC ON THE OTHER SIDE. THE STUDS OF NINE SNAPS GO AROUND THE WAISTBAND. LINER KEPT IN PLACE AT HEM WITH TWO SNAPS: POSTS ON LINER, WITH THE CAPS ON SHORT PIECES OF BLACK NYLON STRAPPING, SEWN TO THE INSIDE OF THE SHELL'S LEG. TWO LABELS, INSIDE WAIST AREA. INSIDE LEFT IS AN OFF-WHITE LABEL WITH RED WRITING, DETAILING PROPER USE OF GARMENT, TO ENSURE SAFETY. BEGINS: "DANGER. DO NOT USE THIS GARMENT IF YOU HAVE NOT READ AND UNDERSTOOD THE ENTIRE FEMSA OFFICIAL USER INFORMATION GUIDE AND ALL LABELS FOR STRUCTURAL FIRE FIGHTING PROTECTIVE GARMENT!" LABEL DETAILS PROPER USE AND ENDS: "COPYRIGHT 1996. FIRE AND EMERGENCY MANUFACTURES AND SERVICES ASSOCIATION, INC. DO NOT REMOVE LABEL." HANDWRITTEN IN BLACK INK, OVERTOP OF THE INITIAL WARNING: "2445617 LETHBRIDGE". ON THE INSIDE RIGHT SIDE IS A WHITE LABEL WITH RED WRITING, DETAILING THE TYPE OF PROTECTION THESE PANTS CAN PROVIDE, AS WELL AS WHAT THEY ARE MADE OUT OF. BEGINS: "GLOBE FIREFITERS SUITS. 37 LOUDON ROAD, PITTSFIELD, NEW HAMPSHIRE, U.S.A. 03263 TEL. 603-435-8323 * FAX: 603-435-6388. THIS GARMENT MEETS THE GARMENT REQUIREMENTS OF NFPA 1971, STANDARD ON PROTECTIVE ENSEMBLE FOR STRUCTURAL FIRE FIGHTING, 2000 EDITION. DO NOT REMOVE THIS LABEL." THIS LABEL ALSO HAS A BLANK SPACES TO FILL IN FOR THE SIZE, LENGTH, CUT, SERIAL #, DATE, AND MODEL NUMBER. THE LABEL ENDS WITH: "IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION STANDARD ON PROTECTIVE ENSEMBLE FOR STRUCTURAL FIRE FIGHTING. NFPA 1971-2000." OVERALL IN GOOD CONDITION. PANTS ARE VERY WELL USED, WITH MANY BLACK STAINS, WHICH ARE ESPECIALLY BAD AT HEM AND KNEES, PARTICULARLY ON THE FRONT OF THE PANTS. RED SUSPENDERS HAVE SOME TEARS, ESPECIALLY IN THE WOVEN STRAPPING. ELASTICIZED STRAPS HAVE LOST SOME OF THEIR ELASTICITY.
Subjects
CLOTHING-OUTERWEAR
Historical Association
SAFETY SERVICES
History
THESE TURNOUT PANTS OR BUNKER PANTS WERE USED BY THE LETHBRIDGE FIRE DEPARTMENT. IN A WRITTEN STATEMENT PROVIDED AT THE TIME OF DONATION, JESSE KURTZ, DEPUTY CHIEF – SUPPORT SERVICES (RETIRED), EXPLAINED THAT THIS COAT WOULD BE “WORN BY ALL FIREFIGHTERS WHEN FIGHTING STRUCTURE FIRES. MADE OF FIRE RESISTANT MATERIAL AND MANUFACTURED ACCORDING TO NATIONAL FIRE PROTECTION AGENCY (NFPA) AND CSA STANDARDS. STANDARDS CHANGE EVERY FIVE YEARS.” IN THE SUMMER OF 2015, COLLECTIONS TECHNICIAN KEVIN MACLEAN, CONDUCTED A SERIES OF INTERVIEWS WITH CURRENT AND FORMER MEMBERS OF THE FIRE DEPARTMENT, INCLUDING: CLIFF “CHARLIE” BROWN (HIRED IN 1966, RETIRED 2004), TREVOR LAZENBY (HIRED IN 1994), RAYMOND “RAY” PETIT (HIRED 1965, RETIRED 1998), AND LAWRENCE DZUREN (HIRED 1959, RETIRED 1992). BROWN SAID: “THESE ARE HIGH CLASS. THESE ARE NICE TURNOUTS. WHAT I HAD IN ’66 WAS JUST AN OLD BLACK CANVAS PANTS AND COAT – LITTLE BIT OF RUBBER LINING INSIDE, ORDINARY HOOKS LIKE THIS. THIS HERE’S GOT VELCRO ON IT; IT’S GOT HOOKS, IT’S GOT ZIPPERS, SORT OF A LINER IN IT FOR HEAT PROTECTION. THIS IS VERY MODERN COMPARED TO WHAT I HAD WHEN I STARTED.” LAZENBY ADDED: “THIS WAS AT LEAST ONE GENERATION AHEAD OF THE JACKET AND PANTS THAT I WAS ISSUED WHEN I WAS NEW. WHEN I WAS NEW, I GOT SECOND HAND TURNOUTS. I GOT STUFF THAT HAD BEEN USED FOR A NUMBER OF YEARS BEFOREHAND … MONEY WAS TIGHT IN THE MID-‘90S WITH COUNCIL AND THE GOVERNMENT PROVINCIALLY, BEING WHAT IT WAS, THERE WAS NOT A LOT TO GO AROUND. … THE HEALTH AND SAFETY MOVEMENT WASN’T AS STRONG THEN AS IT IS NOW. NOW THE HEALTH AND SAFETY MOVEMENT IS VERY POWERFUL AND CAN AFFECT CHANGE IN A HURRY, TO A POINT WHERE WE NOW KNOW THAT SEVEN YEARS OR WHATEVER IT IS AFTER I GET THIS SET OF TURNOUTS, I’M GOING TO GET A NEW SET OF TURNOUTS NO MATTER WHAT. BECAUSE THEY HAVE A SHELF LIFE OF SO MANY YEARS AND ONCE THAT’S UP, YOU’RE NOT ADHERING TO THE STANDARD ANYMORE AND SO IT’S TIME TO CHANGE THEM OUT. WE DIDN’T REALLY GO BY THOSE STANDARDS WHEN I FIRST GOT ON THE JOB, SO I GOT ISSUED STUFF FROM A GUY THAT HAD JUST RECENTLY RETIRED AND I DON’T EVEN THINK THEY GOT SENT TO THE CLEANERS FIRST.” HE CONTINUED, SAYING “THE COMPANIES THAT MAKE THIS GEAR FOR THE FIRST SERVICE … ARE CONSTANTLY SPENDING MILLIONS OF DOLLARS ON RESEARCH AND DEVELOPMENT FOR THE LATEST, GREATEST FIREPROOF FABRIC. THAT GOES DOWN TO WATER VAPOUR BARRIERS, HEAT LINERS, AND THE OUTER SHELL. … YOU KNOW, IT’S A DOUBLE-EDGED SWORD … BECAUSE THE MORE PROTECTED YOU ARE, THE MORE ENCAPSULATED YOU ARE, AND THE LESS YOU FEEL THE AMBIENT TEMPERATURE AROUND YOU, THE MORE TROUBLE YOU CAN REALLY GET YOURSELF IN, RIGHT? THE FURTHER YOU GET INTO A STRUCTURE, THE FURTHER IT IS YOU HAVE TO GET OUT. AND THAT’S ONE OF THE KNOCKS ABOUT, UP UNTIL RECENTLY, OF GETTING THAT MUCH MORE PROTECTION IN YOUR PERSONAL PROTECTIVE EQUIPMENT IS THAT IT WAS LEADING TO PEOPLE MAYBE GOING TO PLACES WHERE 20 YEARS EARLIER THEY COULDN’T HAVE GONE BECAUSE IT WOULD HAVE BEEN TOO HOT.” HE ELABORATED FURTHER: “BUT THE SCIENCE OF FIRE IS BEING BETTER UNDERSTOOD NOW, AS IS OUR TRAINING AND OUR TACTICS. … I THINK I’VE BEEN ISSUED THREE SETS OF TURNOUTS NOW SINCE I GOT MY ORIGINALS … THIS WAS SIMILAR TO MY SECOND SET … I THINK THE ADVANCES IN TECHNOLOGY IN THIS FIELD HAVE BEEN LEAPS AND BOUNDS. THEY’RE JUST SO MUCH BETTER THAN THEY USED TO BE.” IN COMPARING THIS STYLE OF TURNOUT TO WHAT HE CURRENTLY WEARS, LAZENBY SAID: “IT HAS A SHORT BACK ON THE BACK OF THE TURNOUT COAT AND NOW WE HAVE FLAPS THAT COME DOWN. IF YOU WERE TO WEAR THIS JACKET AND YOU DIDN’T HAVE A HIGH BACK ON YOUR TURNOUT PANTS, IF YOU WERE TO BEND OVER, THERE WOULD BE A GAP BETWEEN WHAT YOUR JACKET COVERED AND WHAT YOUR PANTS COVERED. ANY TIME YOU HAVE A GAP, YOU’RE EXPOSING YOURSELF TO EXCESSIVE HEAT … THE FABRICS ARE DIFFERENT NOW, AS IS THE REFLECTIVE STRIPING. … THESE SET WERE NOT AS WELL MADE … THE MATERIAL WASN’T AS HEAT-RESISTANT AND THESE ACTUALLY AREN’T AS REFLECTIVE AS OUR NEW STUFF. THE CUFFS ARE A LITTLE BIT DIFFERENT. I LIKE THE CUFFS THAT THERE’S A THUMBHOLE THAT YOU CAN PUT YOUR THUMB THROUGH THE CUFF SO THAT IT DOESN’T END UP CREEPING UP THE INSIDE OF YOUR JACKET WHEN YOU’RE WORKING. THE CUFF IS AN INTEGRAL PART OF KEEPING DEBRIS AND THINGS OUT OF YOUR COAT AND IF YOU HAVE A COAT THAT TENDS TO RIDE UP YOUR ARM, IT’S NOT IDEAL, SO. JUST LITTLE THINGS THAT ADD UP TO MAKE A BIG DIFFERENCE AFTER/AT THE END OF THE DAY. SO, YEAH, THESE WOULD BE ’95 TO 2000, I THINK.” PETIT ADDED: “THE TURNOUT GEAR IS SO MUCH BETTER, IT’S GONE THROUGH ALL KINDS OF TESTS, DIFFERENT MATERIALS, LIGHTER … ACTUALLY, WE STARTED GETTING BETTER TURNOUTS, AND WHAT THEY WERE DOING WITH THE OLD TURNOUTS THAT WERE NOT GOOD TO US, THEY WERE GIVING THEM TO SMALLER DEPARTMENTS THAT DIDN’T HAVE ANY.” DZUREN DISCUSSED THE TYPE OF TURNOUT GEAR HE WORE WHEN HE FIRST STARTED IN 1959: “THEY WERE JUST STRICTLY KIND OF A CANVAS. THERE WAS NO FIRE-PROOFING TO THEM … I DON’T EVEN BELIEVE THERE WAS ANY FIRE RETARDANT TO THEM. BUT THEN EVENTUALL, WELL THE UNIONS, THEY WERE QUITE ADAMANT, AND THE DEPARTMENTS THEMSELVES WERE QUITE ADAMANT IN TRYING TO KIND OF IMPROVE THAT … WHERE THEY DEVELOPED KEVLAR TYPE STUFF THERE, LIGHTWEIGHT, VERY HEAT RESISTANT, SAVED MANY LIVES WITH THE FACT THAT THEY WERE THAT GOOD.” HE CONTINUED, SAYING: “ONCE THEY CAME IN EVERYBODY WAS QUITE ELATED, THAT THEY DID COME IN, CAUSE’ BEFORE IT WAS ALL JUST STRICTLY BLACK, AND WITH YOUR NAME ON THE BACK, I DON’T EVEN BELIEVE… WELL THEY HAD “L-F-D” ON THE BACK IF I RECALL, AND YOUR NAME, AND THEN THEY WERE HEAVY, AND CUMBERSOME, AND THEY HAD A LINER THERE FOR THE WINTER MONTHS AND A WOOL LINER WAS VERY HEAVY. SO WHEN YOU GOT IN THERE AND YOU START SWEATING, IT WAS NOT IDEAL WORKING GEAR THAT YOU HAD ON WHEN YOU WERE WORKING.” SEE PERMANENT FILE FOR FULL INTERVIEW TRANSCRIPTS AND ADDITIONAL INFORMATION ABOUT THE LETHBRIDGE FIRE DEPARTMENT.
Catalogue Number
P20150010020
Acquisition Date
2015-02
Collection
Museum
Images
Less detail
Other Name
ATTIC LADDER
Date Range From
1960
Date Range To
2010
Material Type
Artifact
Materials
METAL, RUBBER
Catalogue Number
P20150010022
  2 images  
Material Type
Artifact
Other Name
ATTIC LADDER
Date Range From
1960
Date Range To
2010
Materials
METAL, RUBBER
No. Pieces
1
Height
314.2
Length
4.9
Width
33.5
Description
ADJUSTABLE LADDER, SIDE RAILS COME TOGETHER TO MAKE THE LADDER MORE COMPACT (LADDER IS ONLY 8.0CM WIDE WHEN THE SIDE RAILS ARE TOGETHER). SILVER COLOURED METAL, WITH ORANGE PAINT, BLACK RUBBER, AND EIGHT RUNGS. ANTI-SLIP SAFETY SHOE ON THE BOTTOM OF BOTH SIDE RAILS. SAFETY SHOE IS BLACK RUBBER ON THE BOTTOM, WITH A PATTERN OF 10 CIRCLES PER SHOE BOTTOM. METAL TEETH ON THE FRONT OF THE SHOE. SHOES ARE ADJUSTABLE, BUT ARE VERY STIFF. BRACE COMES UP FROM THE BOTTOM AND LOCKS TO PREVENT LADDER RAILS FROM COLLAPSING BACK TOGETHER. BOTTOM OF LADDER HAS A 54.5CM SECTION OF BRIGHT ORANGE PAINT AND TOP HAS A 46.0CM SECTION OF BRIGHT ORANGE PAINT. TOP OF ONE RAIL HAS A BLACK RUBBER TOPPER. SMALL BLACK STICKER AT BOTTOM “P1” WITH SEVERAL STICKERS ON THE OPPOSITE RAIL: A ROUGHLY OVAL SHAPED, RED, BLACK, AND SILVER STICKER: “THIS IS A DUO-SAFETY LADDER. DUO-SAFETY LADDER CORP 519 W 9TH AVE. OSHKOSH, WIS.”; THEN A RECTANGULAR RED STICKER WITH WHITE WRITING: “THIS LADDER IS CERTIFIED TO COMPLY WITH N.F.P.A. SPEC 1931-1832; CURRENT EDITION, FOR FIRE DEPARTMENT GROUND LADDERS AND OSHA FIRE LADDER REQUIREMENTS. REFER TO DUO-SAFETY LADDER SAFETY BOOK FOR CARE – USE – MAINTENANCE ON THIS LADDER. DUO-SAFETY LADDER CORP. OSHKOSH, WI 54901”; THEN A WHITE STICKER WITH GOLD WRITING: “10”. THERE IS ALSO A SILVER COLOURED STICKER WITH HANDWRITING ON THIS SAME RAIL, LOCATED BETWEEN THE FIRST AND SECOND RUNGS: “TEST DATE: 25 NOV 2006. LADDER #: ATTIC #18. APPARATUS #: P1. APPARATUS #: P1.” BOTH RAILS HAVE THE FOLLOWING STICKERS, AT ROUGHLY THE MID-POINT OF THE LADDER: RECTANGULAR, WHITE BACKGROUND, BLUE BORDER, BLACK WRITING: “DANGER. FAILURE TO USE, UNDERSTAND, AND FOLLOW PROPER LADDER USAGE INSTRUCTIONS AS MADE AVAILABLE BY DUO-SAFETY LADDER, N.F.P.A., I.S.F.S.I., A.N.S.I., O.S.H.A., ETC. COULD CAUSE SERIOUS INJURY AND/OR DEATH.” RECTANGULAR, WHITE BACKGROUND, BLACK BORDER AND WRITING: “DANGER. WATCH FOR WIRES. THIS LADDER CONDUCTS ELECTRICITY.” RECTANGULAR, YELLOW, WITH BLACK WRITING: CAUTION. SET UP LADDER PROPERLY TO REDUCE SLIP AND OVERHEAD HAZARDS. FOLLOW THESE INSTRUCTIONS. 1. PLACE TOES AGAINST BOTTOM OF LADDER SIDE RAILS. 2. STAND ERECT. 3. EXTEND ARMS STRAIGHT OUT. 4. PALMS OF HANDS SHOULD TOUCH TOP OF RUNG AT SHOULDER LEVEL. OUT -->” STICKER ON THE INSIDE OF FOURTH RUNG FROM THE BOTTOM: WHITE BACKGROUND, BLACK WRITING: “REMOVE LADDER FROM SERVICE AND TEST IF ANY HEAT SENSOR TURNS DARK -->” LADDER IS IN GOOD OVERALL CONDITION. ADJUSTABLE FEET ARE VERY STIFF. LOTS OF SCUFF MARKS ALL OVER LADDER AND SOME STICKERS HAVE BEEN PARTIALLY REMOVED/SCRATCHED.
Subjects
REGULATIVE & PROTECTIVE T&E
Historical Association
SAFETY SERVICES
History
THIS ATTIC LADDER WAS USED BY THE LETHBRIDGE FIRE DEPARTMENT. IN A WRITTEN STATEMENT PROVIDED AT THE TIME OF DONATION, JESSE KURTZ, DEPUTY CHIEF – SUPPORT SERVICES (RETIRED), EXPLAINED THAT THE LADDER WAS “USED TO ACCESS ATTIC SPACES THROUGH SMALL ACCESS HOLES IN CEILINGS. USED WHEN WE DID NOT WANT TO PULL A CEILING DOWN AFTER A FIRE TO ENSURE THAT THE FIRE IN THE ATTIC WAS OUT.” HE CONTINUED SAYING THAT THIS LADDER WAS DECOMMISSIONED BECAUSE IT IS “OLD AND WORN OUT. ALL LADDERS MUST MEET MINIMUM ACCEPTANCE STANDARDS.” IN THE SUMMER OF 2015, COLLECTIONS TECHNICIAN KEVIN MACLEAN, CONDUCTED A SERIES OF INTERVIEWS WITH CURRENT AND FORMER MEMBERS OF THE FIRE DEPARTMENT, INCLUDING: CLIFF “CHARLIE” BROWN (HIRED IN 1966, RETIRED 2004), TREVOR LAZENBY (HIRED IN 1994), AND LAWRENCE DZUREN (HIRED 1959, RETIRED 1992). BROWN EXPLAINED THAT THIS IS “WHAT WE CALL A LITTLE ATTIC LADDER, TO GET BACK INTO A TIGHT PLACE WHERE YOU COULDN’T BRING A BIG LADDER IN … YOU COULD GET IT UP INTO THE ATTIC SO YOU COULD CHECK WHAT WAS IN THE ATTIC.” LAZENBY ELABORATED: “THIS IS A FOLDING ATTIC LADDER … THE RUNGS THAT SEPARATE THE TWO BEAM SECTIONS ARE ACTUALLY HINGED IN NATURE AND SO IT FOLDS UP AND FITS IN, TYPICALLY, A LITTLE COMPARTMENT ON THE BACK END OF THE TRUCK BECAUSE [THEY] HAVE SOME LONG, LATERAL STORAGE THERE. THESE SURPRISINGLY GET USED A FAIR AMOUNT, STILL.” HE CONTINUED SAYING “THEY’RE NARROW ENOUGH THAT THEY’RE ALMOST DIFFICULT TO CLIMB WITH YOUR BIG FIRE BOOTS ON.” LAZENBY EXPLAINED THAT THE LADDERS IN USE PRESENTLY ARE VERY SIMILAR TO THIS MODEL: “YOU CAN TELL BY LOOKING AT IT IT’S AN OLDER PIECE BUT THE CONSTRUCTION IS ESSENTIALLY THE SAME. THEY MIGHT BE USING SLIGHTLY LIGHTER MATERIALS NOW, BUT FROM WHAT I CAN SEE, THEY’RE BASICALLY THE SAME.” HE ADDED THAT HE WAS OFTEN THE ONE USING THE LADDER: “BECAUSE I WAS NEVER ONE OF THE BIGGER GUYS ON THE JOB, AND ESPECIALLY WHEN I STARTED I WAS PROBABLY TWENTY POUNDS LIGHTER THAN I AM NOW, IF THEY NEEDED SOMEONE TO GET INTO A SMALLER SPACE, I WAS THAT GUY, TYPICALLY, BECAUSE WHEN YOU WEIGHT 250 [POUNDS] AND YOU THROW THE SCBA ON AND ALL THE EQUIPMENT, IT’S DEFINITELY TOUGH FOR SOME OF THOSE GUYS TO GET THROUGH THAT ACCESS. SO, YES, I’VE BEEN IN MY FAIR SHARE OF ATTICS AND THAT’S THE ONLY MEANS TO GET UP THERE.” LAZENBY EXPLAINED THE IMPORTANCE OF USING THE LADDER: “ANY TIME A FIRE VENTS OUT OF A WINDOW AND TOUCHES ANY PART OF THE SOFFIT, IT’S INCUMBENT THAT YOU HAVE TO ABSOLUTELY CHECK THAT BECAUSE IF YOU DON’T AND YOU’RE OPERATING UNDERNEATH AN ATTIC FIRE, THAT’S A VERY, VERY UNSAFE PLACE TO BE.” DZUREN ADDED: “THAT’S A COLLAPSIBLE LADDER. IT’S KIND OF LIKE A SCISSOR TYPE OF LADDER. IT WAS VERY COMPACT, YOU COULD STORE IT ON ONE OF YOUR VEHICLES WITHOUT IT TAKING UP TOO MUCH ROOM … YOU’D CARRY THAT INTO YOUR HOUSE IF AN OFFICER WANTED YOU TO GO UP INTO AN ATTIC … IT WAS EASY TO TRANSPORT AND ONCE YOU GOT IT INTO THE OPENING YOU COULD JUST GIVE IT A SWITCH AND IT WOULD OPEN UP AND YOU COULD JUST CLIMB RIGHT UP TO THE SPOT THERE.” SEE PERMANENT FILE FOR FULL INTERVIEW TRANSCRIPTS AND ADDITIONAL INFORMATION ABOUT THE LETHBRIDGE FIRE DEPARTMENT.
Catalogue Number
P20150010022
Acquisition Date
2015-02
Collection
Museum
Images
Less detail
Other Name
PIERCING NOZZLE
Date Range From
1970
Date Range To
1990
Material Type
Artifact
Materials
BRASS, RUBBER, STEEL
Catalogue Number
P20150010006
  2 images  
Material Type
Artifact
Other Name
PIERCING NOZZLE
Date Range From
1970
Date Range To
1990
Materials
BRASS, RUBBER, STEEL
No. Pieces
1
Length
151.1
Width
10.2
Diameter
6.3
Description
PIERCING NOZZLE. BRASS, WITH CHROME PLATE, STEEL, AND BLACK RUBBER. CYLINDRICAL END OF NOZZLE HEAD IS THREADED, TO ALLOW A HOSE TO BE CONNECTED. TEXTURED EDGE NEAR THREADING. THROUGH THIS OPENING A BLACK RUBBER RING AND METAL MESH ARE VISIBLE. ADJUSTABLE HANDLE EMBOSSED ON ONE SIDE WITH “AKRON BRASS” AND “1 1/2 4 WAP” ON THE OTHER. (NOTE: WAP IS A BEST GUESS, LETTERS HAVE LOST THEIR DEFINITION.) BELOW HANDLE, STAMPED INTO THE METAL BODY OF THE NOZZLE IS “SHUT FOG OPEN”. HANDLE MARKS CHANGE IN SHAPE FROM CYLINDRICAL TO TRIANGULAR. TRIANGULAR PORTION HAS A BLACK STICKER “Q2” AND A STRIPE OF YELLOW PAINT, NEAR THE CONNECTION WITH THE PIPE. A SMALL RECTANGULAR PUSH BUTTON ALLOWS THE NOZZLE TO BE DISCONNECTED FROM THE PIPE. SMALL HOLE THROUGH THE NOZZLE HEAD VISIBLE AT THE CONNECTION OF THE PIPE AND HEAD, WHICH OPENS AND CLOSES WITH THE OPENING AND CLOSING OF THE HANDLE. NEAR THE CONNECTION OF THE PIPE AND HEAD STAMPED INTO THE METAL OF THE PIPE “LFD 62”, WITH THE STAMP BEING PARTIALLY FILLED IN WITH WHITE PAINT. TWO SECTIONS OF STEEL PIPING HAVE BEEN PERMANENTLY THREADED TOGETHER. END OF PIPE HAS THREE SETS OF TWELVE HOLES EACH AROUND THE PIPE, 13.5CM FROM THE END. TIP OF PIPE IS ANGLED, TO CREATE A SHARP END TO PENETRATE THROUGH WALLS. OVERALL GOOD CONDITION. WELL-WORN. CHROME PLATING HAS WORN AWAY, ESPECIALLY ON THE EDGES OF THE HANDLE. LOTS OF SCRATCHES AND SCUFF MARKS ALL OVER. VARIOUS BLACK STAINS ON THE PIPE SECTION.
Subjects
REGULATIVE & PROTECTIVE T&E
Historical Association
SAFETY SERVICES
History
THIS PIERCING NOZZLE WAS USED BY THE LETHBRIDGE FIRE DEPARTMENT. IN A WRITTEN STATEMENT PROVIDED AT THE TIME OF DONATION, JESSE KURTZ, DEPUTY CHIEF – SUPPORT SERVICES (RETIRED), EXPLAINED THAT THIS NOZZLE WAS “USED TO PUT WATER ON THE OTHER SIDE OF A WALL, FLOOR, OR CEILING. ALSO USED TO PUT WATER INSIDE OF A HAYSTACK.” IN THE SUMMER OF 2015, COLLECTIONS TECHNICIAN KEVIN MACLEAN, CONDUCTED A SERIES OF INTERVIEWS WITH CURRENT AND FORMER MEMBERS OF THE FIRE DEPARTMENT, INCLUDING: CLIFF “CHARLIE” BROWN (HIRED IN 1966, RETIRED 2004) AND TREVOR LAZENBY (HIRED IN 1994). BROWN EXPLAINED SAYING: “IT HAS A METAL PROBE ON ONE END OF IT WITH LITTLE HOLES DRILLED INTO IT. MOSTLY WE USED IT FOR BALE FIRES, JAMMING IT INTO THE HAYSTACK OR BALE … ONCE IN A WHILE, WE’D USE IT FOR INSIDE A WALL, BUT VERY SELDOM.” LAZENBY ADDED: “THIS PIECE OF EQUIPMENT … HAS A NUMBER OF NAMES … IT’S BEEN CALLED ANYTHING FROM A CELLAR NOZZLE … TO AN ATTIC NOZZLE, TO A PIERCING NOZZLE … THE POINT ON THE END OF THIS WAS ACTUALLY QUITE SHARP, AND IF YOU WANTED TO, IF YOU HAD AN ATTIC FIRE, YOU COULD EASILY POKE THIS FROM BELOW UP THROUGH YOUR DRYWALL AND YOUR INSULATION … AND THERE WERE A BUNCH OF SMALL HOLES DRILLED INTO THE VERY END SO THAT WHEN YOU DID OPEN IT, THE WATER WOULD COME OUT IN A FOG PATTERN.” HE CONTINUED, SAYING: “THE ADVANTAGE OF THAT IS THAT YOU DIDN’T NECESSARILY HAVE TO PULL THE CEILING DOWN … YOU COULD DO SOME SUPPRESSION UP THERE BEFORE YOU DECIDED TO PULL THAT CEILING DOWN AND SORT OF MAKE CONDITIONS BETTER BEFORE YOU EXPOSED YOURSELF TO THEM. SO FOR THE ATTIC USE, IT WORKED REALLY, REALLY WELL FROM WHAT I HEARD. I’VE NEVER DEPLOYED ONE OF THESE IN THAT SITUATION.” LAZENBY EXPLAINED FURTHER: “THE OTHER USE … IF YOU GOT TO A STRUCTURE AND THE BASEMENT WAS ON FIRE, SAME IDEA, JUST DIFFERENT DIRECTION … IF YOU SHOVED THE NOZZLE DOWN AND OPENED IT UP, YOU’RE GETTING AUTOMATIC SUPPRESSION BEFORE YOU SENT A TEAM DOWN THERE INTO THAT ATMOSPHERE. I WAS EVEN TOLD THAT YOU COULD USE THESE ON AN ENGINE FIRE … SOME OF THESE WERE BUILT WITH A STRIKING SECTION ON THEM SO THAT IF YOU HAD A HAMMER YOU COULD HIT THE TOP OF IT – THIS WOULD ACTUALLY PIERCE THE HOOD OF THE VEHICLE, ENTER THE ENGINE COMPARTMENT, YOU COULD TURN THE NOZZLE ON, AND IT WOULD SUPPRESS THE FIRE WITHOUT EVER HAVING TO LIFE THE HOOD. … I DON’T THINK THAT WE EVER USED THIS TOOL MAYBE AS OFTEN AS WE SHOULD HAVE. I THINK THAT WE, AT TIMES, COULD HAVE MADE BETTER USE AND ACTUALLY MADE CONDITIONS A LITTLE BIT BETTER FOR OURSELVES BEFORE WE PUT OURSELVES INTO THAT SPACE OR ATMOSPHERE.” WHEN ASKED IF THIS TYPE OF NOZZLE IS STILL IN USE, LAZENBY REPLIED: “WE HAVE ONE OF THESE ON OUR ENGINE DOWNTOWN … OURS BREAKS DOWN INTO A COUPLE OF PIECES SO IT STORES EASIER … BUT FUNDAMENTALLY IT’S THE SAME TOOL, SLIGHT MODIFICATIONS FOR EASE OF USE, BUT YEAH, THEY’RE STILL AROUND.” SEE PERMANENT FILE FOR FULL INTERVIEW TRANSCRIPTS AND ADDITIONAL INFORMATION ABOUT THE LETHBRIDGE FIRE DEPARTMENT.
Catalogue Number
P20150010006
Acquisition Date
2015-02
Collection
Museum
Images
Less detail
Other Name
FOLDING CHAIR STRETCHER
Date Range From
1970
Date Range To
2010
Material Type
Artifact
Materials
METAL, VINYL, NYLON
Catalogue Number
P20150010023
  1 image  
Material Type
Artifact
Other Name
FOLDING CHAIR STRETCHER
Date Range From
1970
Date Range To
2010
Materials
METAL, VINYL, NYLON
No. Pieces
4
Height
14.4
Length
221.5
Width
51.2
Description
EMERGENCY FOLDING CHAIR STRETCHER. ADJUSTABLE, MEDIUM BURGUNDY COLOURED VINYL WITH SILVER COLOURED METAL, AND FOUR BLACK RUBBER WHEELS. OUTER RECTANGULAR FRAME WITH A SMALLER, ADJUSTABLE FRAME WITHIN. STRETCHER HAS THREE STRAPS: TWO WINE COLOURED NYLON SEATBELT STYLE STRAPS, WITH METAL AND BLACK PLASTIC BUCKLES, ON THE UPPER BODY. BLACK PLASTIC BUCKLE AT CHEST HEIGHT HAS "FERNO" IN GREY. THIRD BUCKLE IS A BLACK NYLON AND PLASTIC BUCKLE, ON THE LOWER BODY. BACK OF PLASTIC BUCKLE IS EMBOSSED WITH "ACCULOC CSR-10 A.C.W. ASIA, WOONSOCKET RI". RED STICKER WITH WHITE WRITING ON RIGTH SIDE OF STRETCHER, AT WAIST AREA, READS "FERNO". TWO RUBBER FEET AT THE FOOT END OF STRETCHER TO STABILIZE STRETCHER WHEN FULLY EXTENDED. VINYL IS IN TWO PIECES AND CAN BE REMOVED FROM INNER FRAME. GOLD COLOURED ZIPPERS AND SILVER COLOURED SNAPS HOLD VINYL IN PLACE. THERE ARE TWO GOLD ZIPPERS ON THE BACK OF THE FOOT PORTION, BOTH RUNNING VERTICALLY. THERE ARE ALSO TWO GOLD ZIPPERS ON THE BACK OF THE UPPER BODY PORTION, WITH ONE RUNNING HORIZONTALLY AND ONE VERTICALLY. METAL LABEL RIVETED ONTO FRAME AT FOOT OF STRETCHER READS "FERNO - WASHINGTON, INC. WILMINGTON, OHIO, U.S.A. SERIAL NUMBER 07-052255." FOUR FOLDABLE HANDLES, TWO AT HEAD AND TWO AT FEET. HANDLES HAVE TEXTURED BLACK PLASTIC GRIPS. GRIPS EMBOSSED WITH "HUNTWILDE CORPORATION". LOWER HANDLES (AT FOOT) HAVE METAL CYLINDERS THAT SLIDE OVER THE JOINT TO PREVENT HANDLES FROM FOLDING BACK IN. CROSSBAR AT KNEE AREA HAS A SMALL RECTANGULAR PIECE THAT SWINGS OUT AND ONTO A BOLT WHEN STRETCHER IS FOLDED INTO SITTING POSITION, WHICH PREVENTS STRETCHER FROM GOING BACK TO A LAYING DOWN POSITION. UPPER BODY PORTION CAN BE ADJUSTED TO FOUR DIFFERENT POSITIONS: LAYING TOTALLY FLAT TO SITTING AT AN APPROXIMATELY 45 DEGREE ANGLE. AT SHOULDER AREA ON RIGHT SIDE THERE IS A TRIANGULAR SHAPED CLIP, WHICH RELEASES THE UPPER BODY PORTION AND ALLOWS IT TO BE ADJUSTED TO A SITTING POSITION. VERY GOOD TO EXCELLENT CONDITION. VINYL IS STRUCTURALLY VERY GOOD, WITH NO RIPS OR TEARS. SCUFF MARKS AND BLACK STAINS ALL OVER, ESPECIALLY ALONG THE EDGES. METAL FRAME IN VERY GOOD CONDITION. WHEELS AT THE FOOT ARE WORN MORE THAN THOSE AT THE HEAD.
Subjects
LAND TRANSPORTATION-HUMAN-POWERED
Historical Association
SAFETY SERVICES
History
THIS EMERGENCY FOLDING STRETCHER WAS USED BY THE LETHBRIDGE FIRE DEPARTMENT. IN A WRITTEN STATEMENT PROVIDED AT THE TIME OF DONATION, JESSE KURTZ, DEPUTY CHIEF – SUPPORT SERVICES (RETIRED), EXPLAINED THAT THE STRETCHER WAS “USED PRIMARILY IN AMBULANCES FOR MOVING PATIENTS DOWN STAIRS OR AROUND TIGHT CORNERS. WE USE A MORE STAIR FRIENDLY VERSION NOW.” IN THE SUMMER OF 2015, COLLECTIONS TECHNICIAN KEVIN MACLEAN, CONDUCTED A SERIES OF INTERVIEWS WITH CURRENT AND FORMER MEMBERS OF THE FIRE DEPARTMENT, INCLUDING: CLIFF “CHARLIE” BROWN (HIRED IN 1966, RETIRED 2004), TREVOR LAZENBY (HIRED IN 1994), RAYMOND “RAY” PETIT (HIRED 1965, RETIRED 1998), AND LAWRENCE DZUREN (HIRED 1959, RETIRED 1992). BROWN EXPLAINED: “IT WAS MORE OR LESS TO TAKE PEOPLE DOWN STAIRS. SIT THEM UP, STRAP THEM IN, HAD WHEELS ON IT. IT WAS FOR A PERSON THAT DIDN’T HAVE ANY SERIOUS INJURIES MORE OR LESS … IT WAS LIKE A LITTLE CHAIR, FOLD UP, SIT THEM DOWN … GO DOWN THE STAIRS ONE AT A TIME – THUNK, THUNK, THUNK, THUNK.” LAZENBY EXPANDED SAYING: “I HATED THIS STRETCHER. THIS WAS A FOLDING STRETCHER … ACTUALLY THE OLD STAIR-CHAIR, BASICALLY. THEY HAVE MODERNIZED AND IMPROVED THIS DRAMATICALLY. BUT THIS PUZZLE OF A STRETCHER – YOU USED TO BE ABLE TO SET IT UP SO THAT IT CAME INTO A CHAIR … ANY TIME YOU WENT UP INTO AN APARTMENT BUILDING THAT WAS UNDER THREE STORIES, THERE’S NO ELEVATOR, SO YOU SOMETIMES HAD TO CARRY PEOPLE DOWN THREE FLIGHTS OF STAIRS. THIS WAS THE CHAIR OF CHOICE A LOT OF TIMES, IT WAS THE STRETCHER OF CHOICE, BECAUSE IT WAS LIGHTER THAN THE OTHER ONE AND IT WAS EASIER TO MANEUVER AROUND CORNERS … IT WAS A PUZZLE TO PUT TOGETHER AND TO TAKE APART AND I JUST NEVER EVER – I HATED THIS THING. TO THIS DAY, WHEN THE PARAMEDICS SAY ‘WE’RE GONNA NEED THE STAIR CHAIR’, I GRIT MY TEETH AND I CRINGE A LITTLE BIT, I THINK BECAUSE I THINK OF THIS THING, EVEN THOUGH THE NEW ONE IS WAY BETTER. THIS WAS IN SERVICE WHEN I GOT HERE AND I WOULD SAY THAT THIS WAS IN SERVICE ON THE AMBULANCES UNTIL ABOUT … 7 YEARS AGO, GIVE OR TAKE. SO THE BETTER PART OF 15 YEARS THAT THAT WAS IN SERVICE WHILE I WAS HERE.” HE CONTINUED: “THE WORST PART ABOUT THIS IS THAT WHEN YOU PUT A PATIENT ON IT AND YOU LIFTED THEM UP TO GO DOWN THE STAIRS, IT FELT UNSTABLE ENOUGH FOR THEM THAT THEY ALWAYS WANTED TO PUT THEIR ARMS OUT, AND THE SECOND THAT THEY GRABBED ON TO SOMETHING, WELL THEN YOUR CENTRE OF GRAVITY IS LOST AND THEN YOU WERE REALLY IN IT. LIKE YOU THOUGHT, ‘GEEZ, WE COULD ACTUALLY DROP THIS GUY.’ BUT THAT’S WHAT I DISLIKED PROBABLY THE MOST ABOUT THIS THING, OUTSIDE OF HAVING TO PUT IT TOGETHER.” PETIT ADDED: “IF YOU GO TO THE BUILDINGS UP HERE ON LONDON ROAD, SOME TWO STORY BUILDINGS AND THE STAIRS ARE VERY NARROW AND VERY TIGHT, WE USED TO USE THIS TYPE. SO IN OTHER WORDS, INSTEAD OF PUTTING HIM ON A STRETCHER, YOU’D PUT HIM ON THE SEAT. ONE GUY GETS AT THE BACK AND ONE GUY GETS AT THE FRONT AND TAKE THE PERSON DOWN … OVER THE YEARS I GOT A BAD BACK AND GUESS WHERE I GOT THE BAD BACK FROM? IT WAS LIFTING, DOING THINGS LIKE THIS, BECAUSE IT WAS VERY CUMBERSOME.” DZUREN AGREED: “THAT’S JUST A CONFINED SPACE STRETCHER … YOU CAN’T [ALWAYS] GET THE BIG STRETCHER IN, SO YOU CAN PUT THEM ON THAT PARTICULAR ONE. IN AN ELEVATOR, YOU CAN’T GET THAT BIG ONE IN THERE. SOME OF THE ELEVATORS, THE RESIDENTIAL ONES, THEY DON’T, AT LEAST IN THE DAYS GONE BY, THEY DIDN’T THINK ABOUT HAVING TO ACCOMMODATE STRETCHERS. I WOULD PROBABLY SAY IT’S A RARE OCCASION THAT WE HAD TO USE THAT. CAUSE A LOT OF TIMES … IF THE PERSON WAS FAIRLY PHYSICALLY OKAY, YOU COULD TAKE HIM OUT, JUST HOLD HIM. ONE GUY BY THE ARMS, ONE GUY BY THE LEGS, WE HAD A TECHNIQUE THERE WHERE YOU COULD QUITE EASILY TAKE HIM OUT THAT WAY WITHOUT DOING HIM ANY HARM, YOU KNOW. IF HE HAD A BROKEN ARM, WELL, WE COULDN’T DO THAT, SO YOU’D HAVE TO USE ONE OF THOSE.” SEE PERMANENT FILE FOR FULL INTERVIEW TRANSCRIPTS AND ADDITIONAL INFORMATION ABOUT THE LETHBRIDGE FIRE DEPARTMENT.
Catalogue Number
P20150010023
Acquisition Date
2015-02
Collection
Museum
Images
Less detail
Other Name
HIGH VOLUME FIRE HOSE / PUMP LENGTH HOSE
Date Range From
1965
Date Range To
1985
Material Type
Artifact
Materials
NYLON, BRASS, RUBBER,
Catalogue Number
P20150010021
  2 images  
Material Type
Artifact
Other Name
HIGH VOLUME FIRE HOSE / PUMP LENGTH HOSE
Date Range From
1965
Date Range To
1985
Materials
NYLON, BRASS, RUBBER,
No. Pieces
1
Length
416.0
Width
38.3
Diameter
17.5
Description
SHORT HIGH VOLUME FIRE HOSE, ALSO KNOW AS PONY LENGTH OR PUMP LENGTH FIRE HOSE. SHORT, WIDE, RED FIRE HOSE. COUPLINGS ON EACH END OF HOSE. ON THE LARGER END (17.5CM DIAMETER) THE CHROME PLATED COUPLING HAS 10.4CM LONG HANDLES AND A STRIPE OF GREEN PAINT NEAR THE CONNECTION WITH THE HOSE. THE HOSE HAS BEEN TRIPLE CLAMPED ONTO THE COUPLING. ON THE OTHER END OF THE HOSE, THE DIAMETER IS 14.0CM, AND THE COUPLING HAS HANDLES THAT ARE 4.7CM LONG. THIS END OF THE HOSE IS ALSO TRIPLE CLAMPED ONTO THE COUPLING. ON EACH END OF THE HOSE, TWO OF THE CLAMPS ARE SMALLER AND ARE STAMPED WITH A REPEATING "* DENVER * COLORADO * USA * BAND * IT *" THE LARGEST CLAMPS, EACH FURTHEST FROM ITS RESPECTIVE COUPLING, STAMPED: "DIXON V. & C. CO. USA 525" ON EITHER SIDE OF THE TWO LARGE BOLT SETS. VERY GOOD OVERALL CONDITION. CHROME PLATING HAS WORN AWAY ON EDGES. LOTS OF SCRATCHES AND GOUGES IN THE METAL HANDLES OF THE COUPLINGS.
Subjects
REGULATIVE & PROTECTIVE T&E
Historical Association
SAFETY SERVICES
History
THIS HIGH VOLUME FIRE HOSE WAS USED BY THE LETHBRIDGE FIRE DEPARTMENT. IN A WRITTEN STATEMENT PROVIDED AT THE TIME OF DONATION, JESSE KURTZ, DEPUTY CHIEF – SUPPORT SERVICES (RETIRED), EXPLAINED THAT THIS HOSE WAS USED “WHEN A FIRE ENGINE NEEDED TO CONNECT TO A FIRE HYDRANT AND WAS PARKED RIGHT BESIDE THE HYDRANT. THIS WAS BEFORE WE CARRIED LARGER BUT LIGHTER HOSES ON THE TRUCKS.” IN THE SUMMER OF 2015, COLLECTIONS TECHNICIAN KEVIN MACLEAN, CONDUCTED A SERIES OF INTERVIEWS WITH CURRENT AND FORMER MEMBERS OF THE FIRE DEPARTMENT, INCLUDING: CLIFF “CHARLIE” BROWN (HIRED IN 1966, RETIRED 2004), TREVOR LAZENBY (HIRED IN 1994), AND LAWRENCE DZUREN (HIRED 1959, RETIRED 1992). BROWN EXPLAINED THAT “THIS WAS ONE OF YOUR MAIN PIECES OF EQUIPMENT WHEN YOU WENT TO A FIRE … WE’D HOOK THIS [THE HOSE] TO THE HYDRANT, AND THEN THIS INTO OUR PUMP, SO WE’D BE GETTING 8 INCHES OF WATER INTO OUR PUMP, AND THEN THE PUMP WOULD BOOST THAT LINE, AND WE COULD PUT UP 5 OR 6 LINES … THIS WAS ONLY USED AT LARGE FIRES … WHEN WE HAD TO USE THIS, THERE WAS BIG TROUBLE.” LAZENBY ADDED: “IF THIS WAS IN SERVICE WITH OUR DEPARTMENT, THIS WAS IN SERVICE BEFORE I GOT ON, SO I DON’T KNOW THAT I’VE EVEN EVER ACTUALLY SEEN ONE OF THESE, TO BE HONEST WITH YOU.” DZUREN ELABORATED: “THAT’S WHAT WE WOULD HOOK UP ONTO FROM OUR HYDRANT TO THE PUMP. THE HYDRANT MAN, HE WOULD CONNECT THAT TO THE HYDRANT GATE, TO THE HYDRANT, AND THIS WOULD GO TO THE INPUT SIDE OF THE PUMPER. AND THEN THEY WOULD TURN ON THE WATER WITH THAT NOZZLE AND THEY WOULD SUPPLY WATER TO THE FIRE TRUCK AND HE COULD PUMP IT TO A MULTITUDE OF LINES THAT COME OFF OF THERE.” WHEN ASKED WHY FIREFIGHTERS WOULD WANT TO RUN THE WATER THROUGH THE PUMPER TRUCK, RATHER THAN JUST OFF THE HYDRANT, DZUREN EXPLAINED: “WELL, IF THE HYDRANT PRESSURE IS NOT HIGH ENOUGH TO ACCOMMODATE FIREFIGHTING, LIKE SAY IF OUR HOSE, IF A NOZZLE LIKE THAT, YOU’VE GOT TO HAVE UP TO A HUNDRED POUNDS IN THERE, A HYDRANT NORMALLY DOESN’T HAVE THAT KIND OF HIGH PRESSURE.” SEE PERMANENT FILE FOR FULL INTERVIEW TRANSCRIPTS AND ADDITIONAL INFORMATION ABOUT THE LETHBRIDGE FIRE DEPARTMENT.
Catalogue Number
P20150010021
Acquisition Date
2015-02
Collection
Museum
Images
Less detail
Other Name
PIKE HOOK
Date Range From
1970
Date Range To
1990
Material Type
Artifact
Materials
METAL, WOOD
Catalogue Number
P20150010008
  1 image  
Material Type
Artifact
Other Name
PIKE HOOK
Date Range From
1970
Date Range To
1990
Materials
METAL, WOOD
No. Pieces
1
Length
323
Width
11.5
Diameter
4.2
Description
PIKE POLE. LONG, CYLINDRICAL WOODEN HANDLE, WITH A METAL HEAD. THE HEAD IS IN THE SHAPE OF A LOWER CASE 'R', WITH A STRAIGHT AND HOOKED POKER. TWO METAL RIVETS HOLD THE METAL HEAD ON THE WOODEN POLE. NO MARKINGS. FAIR TO GOOD CONDITION. METAL HAS RUSTED. WOOD IS WELL USED AND HAS SEVERAL GOUGES/SLIVERS MISSING. WOOD IS VERY DARK FROM USE. WOOD ESPECIALLY DARK AT JUNCTION WITH METAL HEAD.
Subjects
REGULATIVE & PROTECTIVE T&E
Historical Association
SAFETY SERVICES
History
THIS PIKE POLE WAS USED BY THE LETHBRIDGE FIRE DEPARTMENT. IN A WRITTEN STATEMENT PROVIDED AT THE TIME OF DONATION, JESSE KURTZ, DEPUTY CHIEF – SUPPORT SERVICES (RETIRED), EXPLAINED THAT IT WAS “USED TO PULL CEILINGS FROM BELOW DURING OVERHAUL. ALSO USED TO FORCE CEILINGS DOWN DURING VENTILATION. THE SAME TYPE OF TOOL IS IN USE TODAY.” IN THE SUMMER OF 2015, COLLECTIONS TECHNICIAN KEVIN MACLEAN, CONDUCTED A SERIES OF INTERVIEWS WITH CURRENT AND FORMER MEMBERS OF THE FIRE DEPARTMENT, INCLUDING: CLIFF “CHARLIE” BROWN (HIRED IN 1966, RETIRED 2004) AND TREVOR LAZENBY (HIRED IN 1994). BROWN EXPLAINED “THAT WAS PRETTY IMPORTANT … WHEN YOU HAD A FIRE, AND THE FIRE WAS STILL GOING, BUT MOST OF IT WAS OUT, THE CEILINGS – IF YOU DIDN’T KNOW IF THE FIRE WAS OUT IN THE CEILING, YOU’D TAKE THE PIKE POLE, AND YOU CAN SEE HOW YOU WOULD POKE IT IN … THAT WAS A VERY DESTRUCTIVE TOOL, YOU COULD DO A LOT OF DAMAGE WITH THAT. BUT IF THERE WAS SOMETHING THAT YOU HAD TO GET INTO THE CEILING TO CHECK, AND WE’D OPEN A HOLE IN THE CEILING TO GET UP ON THE LADDER TO LOOK … POKING AROUND TO MAKE SURE THE FIRE WAS OUT.” LAZENBY ADDED: “THIS IS PROBABLY AS CLASSIC A TOOL, A HAND TOOL, AS MAYBE THE PICK HEADED AXE … AS FAR AS FIREFIGHTING GOES. THIS IS A GREAT SALVAGE AND OVERHAUL TOOL … IF YOU HAD A FIRE GO UP INSIDE THE WALLS AND YOU THOUGHT MAYBE THERE WAS FIRE IN THE ATTIC, YOU WOULD NEED TO PULL DOWN THE PLASTER BOARD OR THE LATH OR THE DRYWALL TO … DO A VISUAL INSPECTION OF THAT SPACE.” HE CONTINUED, EXPLAINING ITS USE: “THE POINTY END WAS PERFECT FOR BREAKING THROUGH THE DRYWALL AND ONCE YOU MADE THAT INCISION, FOR LACK OF A BETTER TERM, IF YOU TURNED IT NINETY DEGREES, NOW ALL OF A SUDDEN, THE HOOK IS POINTING TOWARDS A FRESH PORTION OF THE DRYWALL AND AS YOU PULLED, IT WOULD COME DOWN IN RELATIVELY LARGE CHUNKS. AND YOU CAN OPEN UP A FAIR AMOUNT OF CEILING IN A SHORT TIME WITH THIS.” LAZENBY DESCRIBED THE DIFFERENCE BETWEEN THIS PIKE POLE AND MORE MODERN VERSIONS: “THE CONNECTION POINT BETWEEN THE METAL HEAD AND WOODEN HANDLE WOULD WEAKEN AND SOMETIMES THE HEADS WOULD ROCK A LITTLE BIT; THEY WERE TOUGH TO KEEP TIGHT, THEY WOULD RUST A LITTLE BIT. THEY’RE BEING MADE OUT OF DIFFERENT MATERIALS NOW, MOST NOTABLY, THE HANDLES HAVE GONE TO FIBERGLASS. THEY DON’T CONDUCT ELECTRICITY WELL, WHICH IS GOOD. NEITHER DID THE WOOD, BUT AGAIN, NO SPLINTERS, NO SLIVERS, THAT KIND OF THING.” HE REITERATED THE IMPORTANCE OF THIS TOOL: “IT’S ANOTHER GO-TO TOOL FOR US: AXE, HALLIGAN, AND I WOULD SAY PIKE POLE ARE PROBABLY THE THREE MOST COMMONLY USED HAND TOOLS … AND ACTUALLY, IF YOU LOOK, MOST FIRE SERVICE BADGES THAT PEOPLE WEAR – YOU’VE GOT A PIKE POLE AND LADDER – THEY’RE SYNONYMOUS WITH THE FIRE SERVICE.” SEE PERMANENT FILE FOR FULL INTERVIEW TRANSCRIPTS AND ADDITIONAL INFORMATION ABOUT THE LETHBRIDGE FIRE DEPARTMENT.
Catalogue Number
P20150010008
Acquisition Date
2015-02
Collection
Museum
Images
Less detail
Other Name
SELF-CONTAINED BREATHING APPARATUS / AIR MASK AND HARNESS
Date Range From
1975
Date Range To
2000
Material Type
Artifact
Materials
PLASTIC, METAL, COTTON
Catalogue Number
P20150010017
  2 images  
Material Type
Artifact
Other Name
SELF-CONTAINED BREATHING APPARATUS / AIR MASK AND HARNESS
Date Range From
1975
Date Range To
2000
Materials
PLASTIC, METAL, COTTON
No. Pieces
5
Height
29.2
Length
68.8
Width
50.7
Description
SELF-CONTAINED BREATHING APPARATUS, INCLUDES CASE, HARNESS ASSEMBLY, MASK WITH STRAP, AND PAPER PASS CERTIFICATE. .A: CASE. BLACK MOULDED, TEXTURED PLASTIC CASE. ROUGHLY RECTANGULAR SHAPED. HINGED AT THE BACK, CASE HAS THREE HANDLES ON THE FRONT: ONE IS IN THE CENTRE OF THE CASE, WITH THE OTHER TWO ARE ON THE CORNERS OF THE BOX. THERE ARE TWO PLASTIC LATCHES BETWEEN THE THREE HANDLES. BLACK AND SILVER COLOURED STICKER ON THE TOP OF THE BOX READS: "MSA AIRMASK". A SECOND BLACK AND SILVER STICKER, ABOVE ONE OF THE LATCHES, READS: "ULTRALITE PRESSURE DEMAND" AND ALSO HAS "PASS IN BOX" HANDWRITTEN IN BLACKMARKER. A THIRD BLACK AND SILVER STICKER THAT READS "MSA AIRMASK" IS ON THE BOTTOM OF THE BOX. YELLOW PIECE OF DUCT TAPE ON RIGHT SIDE, HANDWRITTEN IN BLACK INK: "ULTRALITE BMR". INSIDE THE BOX IS SUBDIVIDED INTO COMPARTMENTS. AFFIXED TO THE INSIDE TOP OF THE LID IS A PAGE OF INSTRUCTIONS TITLED "MSA AIR MASK, PRESSURE DEMAND TYPE". A SMALL PIECE OF PAPER AFIXED TO THE INSIDE OF THE LID IS TITLED "PACKING ARRANGEMENT" AND HAS AN ILLUSTRATION OF HOW THE UNIT SHOULD BE PACKED AWAY. DIMENSIONS PROVIDED ABOVE CORRESPOND TO THIS CASE. OVERALL IN FAIR TO GOOD CONDITION. THE TWO "MSA AIRMASK" STICKERS HAVE PARTIALLY PEELED AWAY, WITH THE TOP STICKER MISSING THE BOTTOM OF "ASK" IN "MASK" AND WITH THE BOTTOM STICKER MISSING PARTS OF THE "MSA": THE "M" AND "A" ARE PARTIALLY MISSING, WHILE THE "S" IS ENTIRELY GONE; "MASK" OF THIS STICKER IS ALSO VERY DAMAGED. LATCH BELOW THE "ULTRALITE" STICKER IS IN GOOD CONDITION, WHILE THE OTHER IS PARTIALLY BROKEN. SEVERAL SCUFFS AND SCRATCHES IN THE PLASTIC, ESPECIALLY ALONG THE BOTTOM. .B: HARNESS ASSEMBLY. BLACK PLASTIC, METAL, AND FABRIC WITH SILVER COLOURED METAL. OUTER PORTION OF HARNESS DESIGNED TO HOLD BOTTLE OF COMPRESSED AIR. BLACK METAL BRACKET RUNS VERTICALLY UP AND DOWN THE HARNESS AND HAS A SILVER COLOURED CIRCULAR METAL BAND TO HOLD TANK IN PLACE. THE SILVER BAND IS 7.7CM WIDE AND HAS TWO BLACK STICKERS WITH “MSA” IN YELLOW STUCK ON. BOTTOM OF BLACK METAL BRACKET HAS A TRIANGULAR SHAPED PIECE, WITH A ROUND RUBBER TIP, TO HOLD THE BOTTOM OF THE AIR TANK IN PLACE. BELOW SILVER BAND IS A STICKER, WITH A DISCOLOURED WHITE BACKGROUND AND BLACK LETTERS GIVING INSTRUCTIONS FOR USE, ENTITLED: “CUSTOM 4500/ULTRALITE BELT MOUNTED SCBA. OPEN CIRCUIT, PRESSURE-DEMAND ENTRY AND ESCAPE SELF-CONTAINED BREATHING APPARATUS OR COMBINATION SELF-CONTAINED BREATHING APPARATUS AND TYPE C SUPPLIED AIR RESPIRATOR.” SILVER BAND FOR TANK HAS A HANDLE THAT EXPANDS AND CONTRACTS THE BAND, TO ALLOW FOR REMOVAL AND INSTALLATION OF AIR TANK. AT THE TOP OF THE BLACK METAL BRACKET, THERE IS A CIRCULAR SECTION WHICH ALLOWS FOR THE ATTACHMENT OF TWO BLACK PADDED FABRIC SHOULDER STRAPS. THESE STRAPS ARE BOLTED ON WITH BLACK AND SILVER COLOURED BOLTS. BLACK METAL BRACKET ATTACHES AT WAIST AREA TO BLACK MOULDED PIECE OF PLASTIC. BLACK MOULDED PLASTIC FITS AROUND THE HIP AREA OF THE WEARER. SHOULDER STRAPS COME DOWN FROM TOP OF METAL BRACKET AND ATTACH TO THIS BLACK PLASTIC JUST ABOVE THE HIP. SHOULDER STRAPS ARE PADDED AND HAVE A SECOND SMALLER STRAP, WHICH WOULD CROSS THE WEARER’S CHEST WITH A BLACK SIDE RELEASE PLASTIC BUCKLE, WITH THE FEMALE COMPONENT ON THE RIGHT STRAP. ON EACH STRAP BELOW THE PLASTIC BUCKLE IS A SILVER COLOURED “D” RING. ABOVE THE BUCKLE ON EACH STRAP IS A SILVER COLOURED SILK SCREEN SECTION WITH “MSA”. AT THE BOTTOM WAIST PORTION OF THE MOULDED PLASTIC IS ANOTHER BLACK FABRIC STRAP, TO GO AROUND THE WEARER’S WAIST. THE BELT ATTACHES WITH A SILVER COLOURED METAL LATCH PLATE ON THE RIGHT SIDE, WHICH FITS INTO A BLACK PLASTIC BUCKLE, WITH A BLACK PLASTIC BUTTON TO RELASE, ON THE WEARER’S LEFT SIDE. ATTACHED TO THE LEFT SIDE OF THE BELT IS A PRESSURE REGULATOR AND HIGH PRESSURE SUPPLY HOSE. THE PRESSURE REGULATOR CONSISTS OF BLACK METAL AND PLASTIC, AND GOLD AND RED COLOURED METAL. A CIRCULAR GOLD COLOURED METAL PIECE HAS REMNANTS OF TWO STICKERS ON ITS FACE: “MSA AIR MASK – MFD BY MINE SAFETY APPLIANCES COMPANY – PITTSBURGH, PENNSYLVANIA – PRESSURE DEMAND.” BELOW IT IS A HOSE COUPLING. THIS COUPLING HAS A BLACK RUBBER CAP, EMBOSSED WITH “FHR”. BESIDE THIS IS AN AIR PRESSURE GAUGE: BLACK METAL TEXTURED EDGE, GLASS FACE, AND RUBBER ENCASING. THE FACE OF THE GAUGE IS OFF-WHITE WITH A DIAL INCREASING IN INCREMENTS OF 5 (5, 10, 15, 20, 25, 30), WITH A RED SECTION FROM 0-5, A YELLOW SECTION BETWEEN 20 AND 25, AND A GREY SECTION AT 30. BELOW THE DIAL IS “PSI X 100 – USE NO OIL – MSA 18” BESIDE THE GAUGE IS A RED COLOURED METAL KNOB, WITH “ß OPEN – BY PASS” EMBOSSED ON FRONT FACE. BESIDE THIS RED KNOB IS A GOLD COLOURED KNOB WITH A SILVER COLOURED TAB “^PUSH^”. ON THE FACE OF THE GOLD KNOB, EMBOSSED, IS “MAIN LINE ^” WITH “MSA” IN CENTRE. OPPOSITIE THE PRESSURE GAUGE IS A HIGH PRESSURE SUPPLY HOSE. THE HOSE IS BLACK PLASTIC AND FABRIC. ON THE END OF THIS HOSE IS A SILVER COLOURED BELL, USED AS A LOW AIR ALARM. AT THE VERY END OF THE HOSE IS A BLACK TEXTURED METAL COUPLING. .C: MASK WITH HOSE. BLACK PLASTIC RESPIRATOR MASK WITH CLEAR PLASTIC VISOR. FITTED NOSE PIECE WITH TWO SMALL CIRCLES ON EITHER SIDE OF BRIDGE OF NOSE PIECE. EACH CIRCLE HAS BLACK PLASTIC SPOKES AND A TRANSPARENT FLAP, WHICH IS ON THE INSIDE OF THE NOSE PIECE. HANDWRITTEN IN GOLD COLOURED INK, ON THE INSIDE OF NOSE PIECE, “G29C” OR “929C”. FRONT OF NOSE PIECE, VISIBLE THROUGH THE VISOR, HAS “MEDIUM” EMBOSSED ONTO MASK. FIVE BLACK PLASTIC STRAPS WITH SILVER COLOURED BUCKLES ALLOW MASK TO BE SECURELY TIGHTENED ONTO THE HEAD. STRAPS MEET AT A ROUGHLY STAR-SHAPED PIECE THAT SITS AT THE BACK OF THE HEAD. THIS STAR-SHAPED PIECE HAS THE FOLLOWING EMBOSSED ONTO THE PLASTIC: “M2 C5 – MSA – PULL FRONT STRAP LAST – U”. ABOVE THE “M2 C5” IS AN EMBOSSED MULTI-SPOKED CIRCLE. EMBOSSED IN THE CENTRE OF THE CIRCLE: “93 – 94 – 95” EACH OF THE FIVE STRAPS ARE LABELLED; TWO AT THE BASE OF MASK, EACH LABELLED “NECK”, NEXT TWO UP ARE “SIDE”, AND THE FIFTH STRAP AT THE TOP OF THE MASK IS “FRONT”. ON FRONT OF MASK, AT THE MOUTH AREA, IS A LONG ACCORDION-STYLE HOSE. IT IS ATTACHED TO THE MASK WITH A SILVER COLOURED METAL CLAMP. ON THE NUT OF THIS CLAMP IS WRITTEN “ALL STAINLESS BREEZE”. BELOW IS A BLACK METAL BAND, WHICH IS STAMPED IN YELLOW WITH “-18 TINNERMAN”. BELOW THAT THERE IS A SILVER COLOURED METAL RING, WHICH HAS A BLACK FABRIC STRAP ATTACHED (SEE BELOW FOR DESCRIPTION OF THIS ITEM, P20150010017D). THE BOTTOM OF THE HOSE HAS A BLACK METAL BAND AND THEN A SILVER COLOURED, TEXTURED METAL PIECE TO CONNECT TO THE AIR SUPPLY CANISTER. BELOW THE HOSE CONNECTION, AT THE CHIN AREA OF THE MASK, IS A MEDIUM-LIGHT GREY CIRCLE, EMBOSSED WITH “MSA – U.S. PAT. 4,007,758”. TO THE RIGHT OF THE HOSE ATTACHEMENT HANDWRITTEN IN GREEN INK IS “#4”. ON THE RIGHT SIDE OF THE MASK, BETWEEN THE “NECK” AND “SIDE” STRAPS IS A FAINT STAMP IN YELLOW “7-212-“. EMBOSSED IN CENTRE OF MASK, ABOVE FACE VISOR, IS “MSA” IN A CIRCLE. INSIDE OF THE HOSE ATTACHMENT, BELOW THE MOULDED NOSE AREA, IS A BLACK DISK WITH HOLES IN IT. VISIBLE THROUGH THESE HOLES IS A PIECE OF GOLD-COLOURED METAL. DIMENSIONS OF MASK: HOSE IS 83.5CM LONG; VISOR IS 18CM WIDE. .D: STRAP ON MASK. BLACK FABRIC STRAP, WITH TWO BLACK SNAPS. SNAPS ONTO SILVER-COLOURED METAL RING AROUND THE HOSE. STRAP IS 92.5CM LONG AND 1.9CM WIDE. OVERALL CONDITION OF B, C, D: WELL WORN. ALL STICKERS SHOW SIGNS OF WEAR: DISCOLOURATION AND FINISH OF STICKERS SCRATCHED. STRUCTRUALLY IN GOOD CONDITION. MANY SCUFFS AND SCRATCHES ALL OVER. ALL FABRIC IN GOOD CONDITION. RUBBER RETAINS FLEXIBILITY AND PLASTICS ARE IN GOOD SHAPE WITH NO CRACKS. .E: PAPER PASS CERTIFICATE. GOLDENROD COLOURED PAPER. READS: "MSA - ULTRALITE DP - B.M.R. C/W FACEMASK. THIS UNIT TESTED AND HAD ACCEPTABLE PERFORMANCE ON SEPTEMBER 02, 2008. KEN HOBIAK" (WITH KEN'S SIGNATURE ABOVE HIS TYPED NAME). REVERSE OF PAPER: "THIS UNI PERFORM KEN H" (APPEARS TO HAVE MISPRINTED ON THIS SIDE). PAPER IS STANDARD LETTER SIZE. CONDITION IS GOOD: PAPER HAS BEEN CRUMBLED AND HAS A FEW SMALL TEARS AROUND THE OUTSIDE.
Subjects
MINING & MINERAL HARVESTING T&E
Historical Association
SAFETY SERVICES
History
THIS SELF-CONTAINED BREATHING APPARATUS (SCBA) WAS USED BY THE LETHBRIDGE FIRE DEPARTMENT. IN A WRITTEN STATEMENT PROVIDED AT THE TIME OF DONATION, JESSE KURTZ, DEPUTY CHIEF – SUPPORT SERVICES (RETIRED), EXPLAINED THAT THE MASK WAS “USED BY ALL FIREFIGHTERS TO CONNECT TO THE BELT MOUNTED REGULATOR SCBA TO ENTER HAZARDOUS ATMOSPHERES” AND THAT THE HARNESS WAS “USED BY ALL FIREFIGHTERS TO BREATH IN HAZARDOUS (SMOKY) ATMOSPHERES.” HE CONTINUED SAYING THAT THERE ARE “MORE MODERN MASK MOUNTED REGULATOR SCBAS [THAT HAVE BEEN] DEVELOPED AND PURCHASED.” IN THE SUMMER OF 2015, COLLECTIONS TECHNICIAN KEVIN MACLEAN, CONDUCTED A SERIES OF INTERVIEWS WITH CURRENT AND FORMER MEMBERS OF THE FIRE DEPARTMENT, INCLUDING: CLIFF “CHARLIE” BROWN (HIRED IN 1966, RETIRED 2004), TREVOR LAZENBY (HIRED IN 1994), AND LAWRENCE DZUREN (HIRED 1959, RETIRED 1992). BROWN EXPLAINED THAT THIS SCBA “WAS AN ON-DEMAND REGULATOR. THAT WAS NICE TO HAVE DEMAND, BECAUSE NO MATTER WHO IT WAS, THE HARDER YOU BREATHED, THE MORE AIR IT WOULD GIVE YOU. THE HARNESS IS PROBABLY MORE COMFORTABLE [THAN PREVIOUS ONES]. SOME GUYS WOULD USE THREE TANKS, SO THE HARNESS WAS A LITTLE BIT MORE COMFORTABLE FOR THEM. THEY’D COME OUT, THEY’D TURN AROUND, THEY WOULDN’T EVEN TAKE OFF THEIR GEAR. THEY’D TURN AROUND, THERE’D BE GUYS WHO WOULD TAKE THE TANK OFF, PUT ANOTHER TANK ON, HOOK IT ALL UP, A GOOD PAT ON THE BACK, AND BACK IN THEY’D GO WITH ANOTHER TANK. THEY’D DO THAT THREE TIMES BEFORE … THEY WERE JUST TOO TIRED … WE DIDN’T HAVE AN AIR COMPRESSOR TO FILL OUR OWN TANKS. I CAN’T REMEMBER WHERE THEY WENT. THEY MUST HAVE WENT TO THE SWIMMING POOL.” LAZENBY CONTINUED SAYING THAT THIS SCBA WAS “A VERY, VERY OLDER GENERATION SCBA BOTTLE. THESE WERE KIND OF RUDIMENTARY DESIGN. THE BOTTLE WAS STEEL ON THESE, WHICH MADE THEM VERY, VERY HEAVY. MODERN BOTTLES ARE FIBERGLASS WRAPPED WHICH MAKES THEM MUCH, MUCH LIGHTER; ADDED TO WHICH, IT HAD A BARELY PADDED HARNESS SYSTEM ON IT AND BASICALLY A GLORIFIED SEATBELT STRAP FOR A WAIST STRAP. SO WITH THESE KINDS OF THINGS, YOU DON’T WANT TO KEEP A TON OF WEIGHT ON YOUR SHOULDERS BECAUSE IT FATIGUES YOUR UPPER BODY VERY, VERY QUICKLY WHEN YOU’RE WORKING. BUT WITH THIS TYPE OF HARNESS ON THEM, IF YOU CINCHED THE WAIST UP REALLY TIGHT AND TOOK THE PRESSURE OFF YOUR SHOULDERS, THIS JUST SEEMED TO DIG INTO YOUR WAIST LIKE CRAZY, LIKE IT WAS VERY UNCOMFORTABLE TO WEAR … THAT BEING SAID, WHEN GUYS WENT TO THIS FROM LIKE THE CANISTERS THAT THEY USED TO WEAR, THIS MUST HAVE BEEN LIKE A NEW LEASE ON LIFE FOR THESE GUYS … I WORE THESE IN TRAINING – I DON’T THINK I EVER WORE ONE OF THESE BOTTLES ON AN ACTUAL FIRE CALL … WE HAD THE FIBERGLASS ONES IN FRONTLINE SERVICE WHEN I STARTED SO THIS WOULD BE PRE-1994, IF I’M NOT MISTAKEN. I DON’T THINK WE HAD THESE ON THE TRUCKS IN ’94. THEY WERE AROUND AND THEY WERE BACKUPS, BUT THEY WEREN’T FRONTLINE.” HE ELABORATED FURTHER, SAYING: “WE DIDN’T HAVE INDIVIDUAL MASKS; WE SHARED MASKS ON THE FIRE DEPARTMENT BACK THEN … THERE WASN’T ENOUGH MONEY FOR THEM TO BUY US OUR OWN INDIVIDUAL FACE PIECE … SO WHAT WE USED TO DO IS AFTER EVERY INCIDENT OR AFTER EVERY TIME YOU WORE ONE OF THESE THINGS, IT WOULD COME OFF THE TRUCK, WE WOULD HAVE A BOTTLE OF MSA MASK CLEANER THAT WE WOULD PUT INTO A TUB, WE WOULD MAKE A SOAPY WATER SOLUTION, WE WOULD WASH THE MASK, RINSE THE MASK, LET IT HANG TO DRY, AND THE NEXT PERSON WOULD USE IT AS THE NEXT SHIFT CAME ON.” HE ADDED THAT NOW EVERYONE IN THE DEPARTMENT HAS THEIR OWN MASK: “WE’VE HAD OUR OWN MASKS FOR 10-12 YEARS. WE STILL SHARE THE SCBAS AS FAR AS THE BOTTLE AND THE HARNESS GOES … THEY’RE IN THE RACKS ON THE TRUCK, IN THE BACKS OF THE SEATS AND DOWN IN BY THE HOSE OR THE PUMP COMPARTMENTS.” IN DISCUSSING WHY THIS MODEL IS NO LONGER USED, LAZENBY STATED: “THIS HOSE EASILY CRIMPED SO YOUR AIR SUPPLY COULD BE CUT OFF. THE AIR SUPPLY THAT NOW GOES FROM THE TANK TO YOUR MASK IS A MUCH MORE RIGID HOSE THAT, REALLY, YOU’D HAVE TO BASICALLY BEND IT IN HALF TO STOP THE FLOW OF AIR.” DZUREN ADDED FURTHER: “PRIOR TO [THIS] OUR BREATHING APPARATUS WAS WHAT THEY CALLED A CANISTER TYPE OF BREATHING APPARATUS … IT WAS JUST A CANISTER THAT YOU HAD IN FRONT OF YOU HERE AND IT WAS LAYERS OF … GEL, AND SAND, AND SILICA … THERE WAS A SHELF-LIFE WITH THOSE THINGS. IF YOU USED THEM, YOU PRETTY WELL HAD TO DISCARD THEM AFTER YOU USED THEM.” WHEN ASKED WHEN THIS TYPE OF SCBA CAME INTO SERVICE, DZUREN STATED: “I WOULD PROBABLY SAY MAYBE IN THE ‘70S SOMETIME? … I RECALL GUYS GOING IN WHEN WE JUST HAD THOSE CANISTERS. THEY WOULD GO WITHOUT ANYTHING. AND THEY WOULD COME OUT AFTER A WHILE AND THEY WOULD BE BARFING THEIR GUYS OUT … IT SEEMED TO BE, EVEN PRIOR TO MY TIME, WHEN THE STORIES I HEARD FROM GUYS THERE LONGER THAN MYSELF, THAT SEEMED TO BE THE MACHO THING. GET IN THERE AND THEY’D GET IN THERE WITHOUT A MASK. BUT EVENTUALLY, YOU KNOW, BETTER THINKING CAME ALONG AND SAID ‘DON’T BE SILLY, GET SOME STUFF ON THERE.’ BUT ONCE THEY GOT IT, AND THEY STARTED TO USE IT, YOU DID FEEL A LOT BETTER GOING IN, ‘CAUSE PRIOR TO USE GETTING THAT WE HEARD THE HORROR STORIES OF GUYS WHO DID SUCCUMB TO THE ELEMENTS BECAUSE OF ALL THOSE CANISTER TYPES, BUT ONCE THEY GOT [THIS SCBA] IT WAS BETTER.” SEE PERMANENT FILE FOR FULL INTERVIEW TRANSCRIPTS AND ADDITIONAL INFORMATION ABOUT THE LETHBRIDGE FIRE DEPARTMENT.
Catalogue Number
P20150010017
Acquisition Date
2015-02
Collection
Museum
Images
Less detail

8 records – page 1 of 1.